Support Center > Knowledge base> Category: Epilog Zing
Category: Epilog Zing
25 Articles
Orange arrow How do I replace the control/display on my Epilog Zing Laser?

22697 views
  Control/Display Unit Replacement on the Epilog Zing Machine Type: Epilog Zing LaserTools Required: Phillips screwdriver Notes: The control and display units are a single piece. They will be removed and replaced together. Included in the package that you received was an Anti-Static Strap. Wea...
Posted in: Epilog Zing
Tagged: zing, display, control


Orange arrow How do I replace the power supply on my Epilog Zing?

11232 views
  Power Supply Replacement for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Laser Tools Required: Phillips screw driver Lower the table to the bottom of the machine using the focus buttons on the display. Disconnect the machine from its power source. Remove the power cor...
Posted in: Epilog Zing

Orange arrow How do I remove my lens carriage on the Epilog Zing?

18234 views
  Lens Carriage Removal and Installation on the Epilog Zing Laser Machine Type: Zing Engraver Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Move the X-Axis assembly to the center of the machine. M...
Posted in: Epilog Zing
Tagged: optics, lens, lenses, zing


Orange arrow How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser?

18603 views
  X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1.Pic...
Posted in: Epilog Zing

Orange arrow How do I align the laser beam on my Epilog Zing laser?

23842 views
  ...
Tagged: zing, align, laser


Orange arrow How do I replace the Y-Motor on my Zing Laser?

11685 views
  Y-Axis Motor Replacement on the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: #1 Phillips screw driver Remove the back panel form the machine by loosening the captured screws shown in Picture 1.Note: The screws will loosen but you will not be able to remove t...
Posted in: Epilog Zing

Orange arrow How do I replace the Zing X-axis belt?

1024 views
  How do I replace the Zing X-axis belt? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-X-Axis-Belt-Zing.pdf...
Orange arrow How do I replace the Zing backplane board?

733 views
  How do I replace the Zing backplane board? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-Backplane-Board-Zing.pdf...
Orange arrow How do I replace the Zing mirrors?

1002 views
  How do I replace the Zing mirrors? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-mirrors-zing.pdf...
Orange arrow How do I check and adjust the Zing table level?

728 views
  How do I check and adjust the Zing table level? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Checking-Table-Level-Adjustment.pdf...
Orange arrow How do I replace the Zing control and display unit?

585 views
  How do I replace the Zing control and display unit? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Control-Board-replacement.pdf...
Orange arrow How do I replace the Zing laser assembly?

528 views
  How do I replace the Zing laser assembly? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Laser-Assembly-Replacement.pdf...
Orange arrow How do I remove and reinstall the Zing lens carriage?

647 views
  How do I remove and reinstall the Zing lens carriage? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Lens-carrriage-removal-installation.pdf...
Orange arrow How do I replace the Zing power supply?

606 views
  How do I replace the Zing power supply? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-power-supply-replacement.pdf...
Orange arrow How do I replace the Zing table motor?

542 views
  How do I replace the Zing table motor? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Table-Motor-Replacement.pdf...

Page: 1 of 2