Support Center > Knowledge base> Tagged: replace
Tag: replace
13 Articles
Orange arrow How do I replace the control board on my Mini or Helix system?

20477 views
  Control Board Replacement on the Mini and Helix Systems Machine Types: Epilog Mini 18/24, Helix Tools needed: #1 & #2 Phillips head screwdrivers Note: If you are printing through the Ethernet port it is important that you retrieve the parameter for the IP Address, Subnet Mask and Gateway fr...
Orange arrow How do I replace the power supply on my Epilog Zing?

8809 views
  Power Supply Replacement for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Laser Tools Required: Phillips screw driver Lower the table to the bottom of the machine using the focus buttons on the display. Disconnect the machine from its power source. Remove the power cor...
Posted in: Epilog Zing

Orange arrow How do I replace the laser tube in my Epilog Mini or Helix?

27109 views
  Laser Tube Replacement in the Epilog Mini and Helix Machine Types: Epilog Mini 18/24 and Helix Tools needed: Phillips head screwdriver #1 Turn off and unplug the laser system. Facing the back of the machine, remove the 9 screws using the Phillips head screwdriver on the back panel. The l...
Orange arrow How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser?

13536 views
  X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1.Pic...
Posted in: Epilog Zing

Orange arrow How do I replace the lens assembly on the 36EXT?

15684 views
  Replacing the Epilog Legend 36EXT Lens Assembly Although the standard 2" focal lens that comes with the EXT will work well for most projects, to achieve the optimum laser beam on special types of projects, we offer two optional focus lenses. The optional lenses on the Legend 36EXT are designed not...
Posted in: Replacing Optics

Orange arrow How do I replace the X-Axis Read Head on my Mini?

11202 views
  X-Axis Encoder Read Head Replacement on the Mini/Helix Machine Type: Mini 18/24 Tools Required: Large #2 Phillips head screwdriver Small #3 Phillips head screwdriver 3/32 Allen Wrench Make sure the engraver is shut off. Open the plexi-glass window on the engraver. Pull the X-axis beam to t...
Posted in: Epilog Mini

Orange arrow How do I replace the x-axis belt on my Mini?

18861 views
  X-Axis Belt Replacement on the Mini Machine Type: Epilog Mini 18/24 Tools Needed: #1 and #2 Screwdriver Stapler Turn off the machine and unplug the power cord. Remove the left side panel from the engraver by removing the six screws that fix it to the body of the Mini or Helix. T...
Posted in: Epilog Mini
Tagged: replace, x-axis, mini, belt


Orange arrow How do I install the keyboard on my Epilog Mini?

8850 views
  Keyboard Installation on the Mini Machine Type: Epilog Mini 18/24 Tools Needed: #1 Phillips Head Screwdriver Turn machine off and unplug power cord from side of engrave. You will need to remove both the left and right hand side covers that have the hand holds. These are attached to the machi...
Posted in: Epilog Mini

Orange arrow How do I replace the flex cable on my Epilog Mini?

10551 views
  X-Axis Flex Cable Replacement on the Epilog Mini Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam.Picture 1 Remove I-Beam cover by loosening the two screws on the fron...
Posted in: Epilog Mini

Orange arrow How do I install a new display on my Epilog Mini or Helix?

8313 views
  Display Installation on the Mini/Helix Machine Types: Epilog Mini 18/24 and Helix Tools Needed: #1 Phillips Head Screwdriver Turn the engraver off and unplug the power cord from the side of the engraver. You will need to remove both the left and right hand side covers that have the h...
Orange arrow How do I replace the laser in my Zing Laser?

11516 views
  Machine Type: Epilog Zing 16 and 24 Lasers Tools Required: #1 Phillips screw driver Lower the table to the bottom of the machine. Turn off the machine. Disconnect the machine from its power source. Remove the four Phillips screws which secure the left hand side panel. There a...
Posted in: Epilog Zing

Orange arrow How do I install the Super-Silent Fans in my Mini or Helix?

11544 views
  Super-Silent Fans Installation Instructions for the Epilog Mini and Helix Machine Types: Epilog Mini 18/24 and HelixTools Needed: #1 Phillips Head Screwdriver 5/16 nut driver Turn off and unplug the engraver from the power source. Facing the rear of the machine, remove the eight Phillips s...
Orange arrow How do I replace the fans on my Epilog Mini or Helix System?

10993 views
  Fan Replacement on the Epilog Mini and Helix Systems Machine Type: Epilog Mini 18/24 and Helix Tools Needed: #2 Phillips head screwdriver, 6/32 Nut driver Flat head screwdriver or wire cutter Turn engraver off and unplug it from the wall. Face the back of the machine where the ex...

Page: 1 of 1