Service- und Reparaturarchiv

So ersetzen Sie die Kabel der Überkopfkamera

Erfahren Sie in dieser Schritt-für-Schritt-Videoanleitung, wie Sie die Kabel der Überkopfkamera bei den Lasersystemen Epilog Fusion Edge, Maker und Pro 24/36 austauschen.

09/23/2025

So installieren Sie das Zugentlastungs-Kit

Wie installiere ich das Zugentlastungsset an meinem epilog laser?

Estimated time: 10–15 minutes • Skill: Basic This guide explains how to install the strain relief kit on the lens carriage of your Epilog Laser system. The kit includes a harness clamp and mounting hardware designed to guide and secure the autofocus and camera cables as they move with the (...)

09/19/2025

LC1000 – Übersicht über Anschlüsse und LEDs des Steuermoduls

The control module on Epilog laser systems provides connection points and LED indicators that offer system status and control feedback. This guide outlines each port and indicator located on the right side of the machine. Port Descriptions Exhaust Control: Connects to a compatible exhaust unit to send on/off commands. USB (...)

03/24/2026

Reinigung und Schmierung der Linearführung (IKO)

This guide provides detailed instructions for cleaning and greasing the linear guide rail on your Epilog Laser system. Over time, debris and buildup can affect motion smoothness and engraving accuracy. Performing regular maintenance helps ensure optimal performance and extends the life of your equipment. Follow each step carefully, and refer (...)

12/30/2025

SD-Karten flashen

Erfahren Sie, wie Sie eine SD-Karte für Epilog Laser mit Balena Etcher flashen können.

This guide outlines the steps for flashing an SD card for your laser system. A technician must provide the required disc image file to complete this process. Do not proceed without first obtaining the correct file specific to your machine. Flashing SD Cards SD Card Removal Remove the control board (...)

06/19/2025

Assistent zur Kalibrierung des Autofokus

Estimated Time: 2–5 Minutes | Skill Level: Basic The Autofocus Calibration Wizard allows the laser system to automatically determine the correct autofocus height using a calibrated reference surface. This process ensures accurate and consistent autofocus performance across supported materials. Running the Autofocus Calibration Wizard Open the Settings Menu (...)

03/24/2026

Fokus-Kalibrierungsassistent

Schrittweise Anleitung zur Verwendung des Fokuskalibrierungsassistenten, verfügbar in Firmware-Version 1.1.2.1 und höher.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/16/2026

Pro 24, Pro 36

Ersatz für Linearführung (IKO) – Large Aperture Fusion Pro

Removal Procedure Power OFF the machine and disconnect the power cord. Remove the right and left side panels. Open the top door. Pull the rail to the middle of the machine. Move the carriage to the center. Loosen the thumb screws and open the mirror cover. Disconnect the air assist (...)

05/20/2025

Pro 24, Pro 36

Ersatz des Autofokus-Schalters – Fusion Maker, Edge, Pro 24 & 36

Wie ersetze ich den Autofokus-Schalter im Fusion Maker, Edge und Pro 24 und 36?

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

05/07/2025

Wartung und Reparatur

Filter

Filter

Vorbeugende Wartung von Lasersystemen

LC1000-TS Diagnoseassistent

Einstellung der X-Achsen-Riemenführung

So ersetzen Sie die Kabel der Überkopfkamera

So installieren Sie das Zugentlastungs-Kit

LC1000 – Übersicht über Anschlüsse und LEDs des Steuermoduls

Reinigung und Schmierung der Linearführung (IKO)

SD-Karten flashen

Assistent zur Kalibrierung des Autofokus

Fokus-Kalibrierungsassistent

Ersatz für Linearführung (IKO) – Large Aperture Fusion Pro

Ersatz des Autofokus-Schalters – Fusion Maker, Edge, Pro 24 & 36