Service- und Reparaturarchiv

Fokus-Kalibrierungsassistent

Schrittweise Anleitung zur Verwendung des Fokuskalibrierungsassistenten, verfügbar in Firmware-Version 1.1.2.1 und höher.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/16/2026

Pro 24, Pro 36

Ersatz für Linearführung (IKO) – Large Aperture Fusion Pro

Removal Procedure Power OFF the machine and disconnect the power cord. Remove the right and left side panels. Open the top door. Pull the rail to the middle of the machine. Move the carriage to the center. Loosen the thumb screws and open the mirror cover. Disconnect the air assist (...)

05/20/2025

Pro 48

Netzteilaustausch – Fusion Pro 48 200 Watt

Schritt-für-Schritt-Anleitung zum Austausch des Netzteils in einem Fusion Pro 48 .

WARNING: Servicing the power supply while the engraver is powered on can cause serious injury or damage to internal components. Always disconnect all power sources before beginning. Power Supply Removal Power OFF the system and disconnect the power cable. Remove the rear-top panel. Disconnect all electrical harnesses from the power (...)

05/19/2025

Pro 24, Pro 36

Ersatz des Autofokus-Schalters – Fusion Maker, Edge, Pro 24 & 36

Wie ersetze ich den Autofokus-Schalter im Fusion Maker, Edge und Pro 24 und 36?

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

05/07/2025

Optikreinigung – Fusion Maker, Edge und Pro

Dieses Dokument beschreibt, wie die Optik des Fusion Maker, Edge und Pro Carriage ordnungsgemäß gereinigt wird.

Daily Maintenance Cleaning Remove the lens and carriage mirror. Safely detach both the lens and carriage mirror using the video guide below. Figure 1. Lens and carriage mirror removal process. Carriage Optics Removal Steps Disconnect the air tubing from the lens. Loosen the thumb screws on the carriage cover and (...)

12/31/2025

Meine Kunstwerke werden nicht im Epilog-Dashboard angezeigt.

Mein Kunstwerk wird nicht im Epilog-Dashboard angezeigt und die Laufzeit wird mit 0:00 angegeben?

Explanation of the Symptoms When encountering this issue, you may see something similar to the image below—here we can see the artwork in the preview thumbnail, but the artwork does not appear in the work area: However, if zoomed out, we can see that the artwork did transfer to the (...)

04/25/2025

Pro 24, Pro 36

Manuelle Kalibrierung der Fokussieranzeige – Fusion Maker, Edge, Pro

Erfahren Sie, wie Sie die manuelle Fokussieranzeige an einer Fusion Maker-, Edge- oder Pro-Maschine kalibrieren.

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

12/31/2025

Pro 24, Pro 36

So ersetzen Sie den X-Achsen-Motortreiber: Schritt-für-Schritt-Anleitung

Erfahren Sie, wie Sie die X-Achsen-Antriebsplatine TE0104 bei Maschinen der Serien 17000 Edge und Pro austauschen. Diese Reparatur kann möglicherweise verschiedene Probleme mit der Bewegung der X-Achse beheben und dazu beitragen, einen reibungslosen Betrieb wiederherzustellen.

This guide will walk you through the process of removing, installing, and programming the X-Axis Drive Board for Fusion Edge and Pro 24 / 36 models. Proper precautions, including the use of an anti-static strap, are essential to ensure the safe handling of electronic components. Drive Board Replacement Procedure Models: (...)

11/11/2025