Service- und Reparaturarchiv

Y-Motor-Ersatz

Ersetzen Sie den Motor, der die X-Achsen-Baugruppe Ihrer Maschine vorwärts und rückwärts bewegt.

Remove Right Panel Remove the right side panel by removing the 6 screws, 4 located on the side of the machine, two located on the back of the machine. Remove Old Y-Motor Open the front access door. Locate the Y-Motor on the right hand-side of the machine. Remove the spring (...)

09/24/2024

X-Motor-Austausch

Ersetzen Sie den Motor, der den Laserkopf Ihrer Maschine entlang der X-Achsen-Baugruppe bewegt.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

04/11/2025

Hohe Wattzahl

Behebung eines Stromproblems: Austausch des doppelten Netzteils

So ersetzen Sie das Helix .

Remove Back Panel Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the two power supplies. Disconnect Electrical Leads Disconnect four of the electrical leads. Disconnect the two connectors holding (...)

10/14/2025

Geringe Wattzahl

Behebung eines Stromproblems: Austausch des Netzteils

So ersetzen Sie das Helix netzteil.

Remove Old Power Supply Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the power supply on the left hand side of the machine. Disconnect the three electrical leads. With (...)

10/14/2025

Ersetzen des Displays/der Tastatur

Ersetzen Sie das Bedienfeld/die Tastatur Ihrer Maschine.

Remove Side Panels Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove (...)

04/14/2025

CO2 -Tickle-Einstellungen

Was sind Kitzel-Einstellungen und wie kann ich sie anpassen?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

04/02/2025

Optikaustausch –Helix

Wie wechsle ich die Linse in meiner Helix Mini?

This guide provides step-by-step instructions for replacing the carriage, steering, and periscope optics in your laser system. Follow the outlined procedures carefully to ensure proper installation and alignment. Always handle optics with care and refer to the provided alignment links after replacement to maintain optimal performance. Replacing Carriage Optics Move (...)

04/03/2025

Erweiterte Anleitung zum Kaltstart

Mein Laser ist seit langer Zeit inaktiv und feuert nicht.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

04/08/2025

Überprüfen und Nivellieren des Tisches

Wenn Sie ungleichmäßige Gravuren oder eine verminderte Leistung an bestimmten Ecken Ihres Mini oder Helix feststellen, ist der Tisch möglicherweise nicht waagerecht ausgerichtet. In dieser Anleitung wird erklärt, wie Sie den Tisch überprüfen und ausrichten können, um eine optimale Leistung zu erzielen.

Estimated time: 15-20 minutes • Skill: Beginner A perfectly level engraving table is essential for accurate focusing and consistent engraving results. This guide will walk you through checking and adjusting the table level on your Epilog Mini or Helix laser system. Checking Table Level Access the table. Power on the (...)

10/23/2025