Service- und Reparaturarchiv

Autofokus-Stößel einbauen

Wie ersetze ich den Autofokus-Stößel an meinem Mini helix ?

Estimated time: 15 minutes • Skill: Beginner This procedure walks you through replacing the Auto Focus Plunger on your laser system. Following these steps carefully will ensure proper installation and reliable autofocus operation after the replacement is complete. Component Overview Exploded view of the carriage assembly Preparation Power on the (...)

02/09/2026

Ersatz des X-Achsen-Riemens – Mini / Helix

Wie ersetze ich den Riemen der X-Achse meines Mini?

Estimated time: 15–20 minutes • Skill: Basic This guide walks you step-by-step through replacing the X-Axis belt on an Epilog Mini or Helix laser engraver. Follow each instruction carefully to ensure proper installation and avoid damaging your machine. Always power off and unplug the engraver before beginning. To complete this (...)

10/03/2025

Installation des flexiblen Kabels der X-Achse – Mini / Helix

Wie ersetze ich das Flexkabel meines Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam. Picture 1 Remove I-Beam cover by loosening the two screws on the front side of the beam and the four screws on the rear if you (...)

04/08/2025

X-Achsen-Schienenmontage

Wie ersetze ich die X-Achsen-Schiene meines Epilog Mini?

Machine Type: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver Small Philips head screw driver Flat head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit Intro: This procedure details steps to replacing the X-Axis rail on the Legend Mini. The X-Axis rail guides the (...)

04/08/2025

Einbau der linearen Führung der X-Achse

Wie ersetze ich das Linearlager in meinem Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit This procedure details steps to replacing the X-axis bearing set. The bearing set is the race and bearing bracket that guides the X-Axis carriage assembly from left to (...)

09/27/2024

Genauigkeit wiederherstellen: Austausch des X-Achsen-Encoderstreifens

Wie ersetze ich den X-Achsen-Encoderstreifen für meinen Epilog Mini, Helix oder FiberMark?

Estimated time: 20–30 minutes • Skill: Basic This guide explains how to replace the encoder strip and reader assembly on the Epilog Mini, Helix, or FiberMark laser system. The encoder strip is the thin clear plastic strip that the encoder reader reads to determine X-Axis position; replacing it restores reliable (...)

10/15/2025

X-Motor-Austausch

Ersetzen Sie den Motor, der den Laserkopf Ihrer Maschine entlang der X-Achsen-Baugruppe bewegt.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

04/11/2025

Ersatz der X-Achsen-Baugruppe

Ersetzen Sie den Portalkran, der über die X-Achse Ihrer Maschine verläuft.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

09/24/2024

Montage der X-Achse – FiberMark

Wie entferne ich die FiberMark ?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

10/02/2025

X-Achse

Filter

Filter

Autofokus-Stößel einbauen

Ersatz des X-Achsen-Riemens – Mini / Helix

Installation des flexiblen Kabels der X-Achse – Mini / Helix

X-Achsen-Schienenmontage

Einbau der linearen Führung der X-Achse

Genauigkeit wiederherstellen: Austausch des X-Achsen-Encoderstreifens

X-Motor-Austausch

Ersatz der X-Achsen-Baugruppe

Montage der X-Achse – FiberMark