Archivos de servicio y reparación

Cómo sustituir los cables de la cámara superior

Aprenda a sustituir los cables de la cámara superior en los sistemas láser Epilog Fusion Edge, Maker y Pro 24/36 con esta guía en vídeo paso a paso.

09/23/2025

Cómo instalar el kit de alivio de tensión

¿Cómo instalo el kit de alivio de tensión en mi epilog laser?

Estimated time: 10–15 minutes • Skill: Basic This guide explains how to install the strain relief kit on the lens carriage of your Epilog Laser system. The kit includes a harness clamp and mounting hardware designed to guide and secure the autofocus and camera cables as they move with the (...)

09/19/2025

LC1000: descripción general del puerto del módulo de control y los LED

The control module on Epilog laser systems provides connection points and LED indicators that offer system status and control feedback. This guide outlines each port and indicator located on the right side of the machine. Port Descriptions Exhaust Control: Connects to a compatible exhaust unit to send on/off commands. USB (...)

03/24/2026

Limpieza y engrase de la guía lineal (IKO)

This guide provides detailed instructions for cleaning and greasing the linear guide rail on your Epilog Laser system. Over time, debris and buildup can affect motion smoothness and engraving accuracy. Performing regular maintenance helps ensure optimal performance and extends the life of your equipment. Follow each step carefully, and refer (...)

12/30/2025

Tarjetas SD parpadeantes

Aprenda a grabar una tarjeta SD para Epilog Laser utilizando Balena Etcher.

This guide outlines the steps for flashing an SD card for your laser system. A technician must provide the required disc image file to complete this process. Do not proceed without first obtaining the correct file specific to your machine. Flashing SD Cards SD Card Removal Remove the control board (...)

06/19/2025

Asistente para calibración del enfoque automático

Estimated Time: 2–5 Minutes | Skill Level: Basic The Autofocus Calibration Wizard allows the laser system to automatically determine the correct autofocus height using a calibrated reference surface. This process ensures accurate and consistent autofocus performance across supported materials. Running the Autofocus Calibration Wizard Open the Settings Menu (...)

03/24/2026

Asistente para calibración del enfoque

Guía paso a paso para utilizar el asistente de calibración de enfoque, disponible en la versión de firmware 1.1.2.1 y posteriores.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/16/2026

Pro 24, Pro 36

Sustitución de guía lineal (IKO) – Fusion Pro de gran apertura

Removal Procedure Power OFF the machine and disconnect the power cord. Remove the right and left side panels. Open the top door. Pull the rail to the middle of the machine. Move the carriage to the center. Loosen the thumb screws and open the mirror cover. Disconnect the air assist (...)

05/20/2025

Pro 24, Pro 36

Sustitución del interruptor de enfoque automático – Fusion Maker, Edge, Pro 24 y 36

¿Cómo se sustituye el interruptor de enfoque automático en los modelos Fusion Maker, Edge y Pro 24 y 36?

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

05/07/2025

Servicio y reparación

Filtros

Filtros

Mantenimiento preventivo del sistema láser

Asistente de diagnóstico LC1000-TS

Ajuste del seguimiento de la correa del eje X

Cómo sustituir los cables de la cámara superior

Cómo instalar el kit de alivio de tensión

LC1000: descripción general del puerto del módulo de control y los LED

Limpieza y engrase de la guía lineal (IKO)

Tarjetas SD parpadeantes

Asistente para calibración del enfoque automático

Asistente para calibración del enfoque

Sustitución de guía lineal (IKO) – Fusion Pro de gran apertura

Sustitución del interruptor de enfoque automático – Fusion Maker, Edge, Pro 24 y 36