Archives des services et réparations

Remplacement de la courroie de l'axe X – Mini / Helix

Comment remplacer la courroie de l'axe X sur ma Mini ?

Estimated time: 15–20 minutes • Skill: Basic This guide walks you step-by-step through replacing the X-Axis belt on an Epilog Mini or Helix laser engraver. Follow each instruction carefully to ensure proper installation and avoid damaging your machine. Always power off and unplug the engraver before beginning. To complete this (...)

10/03/2025

Installation du câble flexible de l'axe X – Mini / Helix

Comment remplacer le câble flexible de mon Epilog Mini ?

Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam. Picture 1 Remove I-Beam cover by loosening the two screws on the front side of the beam and the four screws on the rear if you (...)

04/08/2025

Installation du rail de l'axe X

Comment remplacer le rail de l'axe X sur mon Epilog Mini ?

Machine Type: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver Small Philips head screw driver Flat head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit Intro: This procedure details steps to replacing the X-Axis rail on the Legend Mini. The X-Axis rail guides the (...)

04/08/2025

Installation du guide linéaire de l'axe X

Comment remplacer le roulement linéaire de mon Epilog Mini ?

Machine Types: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit This procedure details steps to replacing the X-axis bearing set. The bearing set is the race and bearing bracket that guides the X-Axis carriage assembly from left to (...)

09/27/2024

Restaurer la précision : remplacement de la bande codeuse de l'axe X

Comment remplacer la bande encodeuse de l'axe X de mon Epilog Mini, Helix ou FiberMark?

Estimated time: 20–30 minutes • Skill: Basic This guide explains how to replace the encoder strip and reader assembly on the Epilog Mini, Helix, or FiberMark laser system. The encoder strip is the thin clear plastic strip that the encoder reader reads to determine X-Axis position; replacing it restores reliable (...)

10/15/2025

Guide complet : Retrait du rail et de la courroie de l'axe X

Comment remplacer la courroie de l'axe X sur la FiberMark?

Estimated time: 30–45 minutes • Skill: Intermediate To replace the X-Axis belt on an Epilog FiberMark laser, you must remove the X-Axis rail to allow access to the bearing guard and proper belt routing. This procedure involves three phases: removing the rail, replacing the belt, and reinstalling the rail and (...)

10/15/2025

Installation de l'ensemble axe X – FiberMark

Comment retirer l'ensemble FiberMark ?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

10/02/2025

Installation du moteur de l'axe X – FiberMark

Comment remplacer le moteur X sur le FiberMark?

Estimated time: 15–20 minutes • Skill: Basic This guide explains how to replace the X-motor on the Epilog FiberMark laser system. The X-motor is responsible for moving the lens carriage from left to right along the X-axis. Following these instructions will help you safely remove the old motor and install (...)

10/02/2025

Axe X

Filtres

Filtres

Remplacement de la courroie de l'axe X – Mini / Helix

Installation du câble flexible de l'axe X – Mini / Helix

Installation du rail de l'axe X

Installation du guide linéaire de l'axe X

Restaurer la précision : remplacement de la bande codeuse de l'axe X

Guide complet : Retrait du rail et de la courroie de l'axe X

Installation de l'ensemble axe X – FiberMark

Installation du moteur de l'axe X – FiberMark