- Acceleration Match Offset [cnts]
- Number of encoder counts to delay firing laser when accelerating. Used for raster quality adjustments
- Deceleration Match Offset [cnts]
- Number of encoder counts to delay firing laser when decelerating. Used for raster quality adjustments
- Bed Margins [in]
- The margins around the bed, in inches that the carriage can travel to.
- Format is as follows: TOP,LEFT,BOTTOM,RIGHT
- Bed Size [in]
- The size of the bed in the machine in inches
- Format is as follows: WIDTH,HEIGHT
- Requires “Home Axis” to take effect
- Disable Table Homing
- Setting to disable homing the table when the machine boots. For optimal operation, leave this at a value of 0
- A value of 1 will disable table homing
- Will take effect after reboot
- Rotary Encoder [cnts/in]
- The number of encoder counts per inch of travel for the rotary device
- Requires “Home Axis” to take effect
- X Axis Encoder [cnts/in]
- The number of encoder counter per inch of travel for the X Axis
- Requires “Home Axis” to take effect
- Must recalibrate cameras if this changes
- Y Axis Encoder [cnts/in]
- The number of encoder counter per inch of travel for the Y Axis
- Requires “Home Axis” to take effect
- Must recalibrate cameras if this changes
- Home Offset [in]
- The offset of the table origin, relative to the X and Y limit switches
- Requires “Park Axis” to take effect
- Must recalibrate cameras if this changes
- Joystick Center X
- The center X position of the joystick, in joystick units
- Joystick Center Y
- The center Y position of the joystick, in joystick units
- Joystick Deadzone [%/100]
- The percentage of dead zone around the center of the joystick
- Joystick Limit X
- The MIN and MAX limits for the X axis of the joystick, in joystick units
- Format is as follows: MIN,MAX
- Joystick Limit Y
- The MIN and MAX limits for the Y axis of the joystick, in joystick units
- Format is as follows: MIN,MAX
- Laser Match [cnts]
- Adjustment to synchronize left to right and right to left raster lines. Units are in number of encoder counts
- Laser Match Offset [cnts]
- Offset of the raster data in X. Used to align raster and vector if needed. Units are in number of encoder counts
- Velocity Match Offset [cnts]
- Offset of the raster data proportional to velocity. Units are in number of encoder counts
- Park Position [in]
- The position in inches to park the laser head when the machine is idle
- Requires “Park Axis” to take effect
- Plunger Offset [cnts]
- The number of table encoder counts from the laser zero focus position, to the auto focus plunger
- Rotary Offset [in]
- The offset of the rotary origin, relative to the X and Y limit switches
- Rotary Table Height [in]
- The distance in inches to clear the rotary device
- Scale [mm/in]
- A scale factor to adjust the scale of the X and Y axis
- Format is as follows: X,Y
- Requires “Home Axis” to take effect
- Must recalibrate cameras if this changes
- Table Switch Locations [cnts]
- A list of the locations in which the table switches were located
- Table Current [A]
- The current in Amps to run the table drive
- Table Resolution [cnts/in]
- The number of encoder counts per inch of travel for the table
- Must “Home Table” if this value is changed
- CO2 Tickle Duration [us]
- The duration of the laser tickle pulse in microseconds
- CO2 Tickle Frequency [Hz]
- The frequency of the laser tickle pulse in hertz
- CO2 Tickle Holdoff [us]
- The duration in which the laser tickle is stalled after a laser pulse in microseconds
- CO2 Pulse Stretch [us]
- The amount to stretch all laser pulses in microseconds
- Table Focus Offset [cnts]
- The distance in table encoder counts from the top crash switch, to the laser focus position
- RHS Y Skew [cnts]
- The number of encoder counts to skew the right hand side of the Y axis after homing
- Requires “Home Axis” to take effect
- Air Assist Delay [s]
- The number of seconds to delay turning ON and turning OFF the air assist before and after a job finished
- Format is as follows: ON,OFF