Kalibraties

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/24/2026

Wizard voor het kalibreren van de focus

Stapsgewijze handleiding voor het gebruik van de Focus Calibration Wizard, beschikbaar in firmwareversie 1.1.2.1 en hoger.

03/16/2026

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

Handmatige kalibratie van de focusmeter – Fusion Maker, Edge, Pro

Leer hoe je de handmatige focusmeter op een Fusion Maker-, Edge- of Pro-machine kunt kalibreren.

Estimated Time: 20–40 Minutes • Skill Level: Intermediate Important: All focus calibration procedures must be completed before performing a camera calibration to ensure accurate results. Click the tabs below to switch between machine types. Each tab shows the camera calibration procedure specific to that machine. Overview & Requirements Fusion Edge (...)

Pro 24/36, Pro 32/48

Handleiding voor het kalibreren van de IRIS-camera

Hoe kalibreer ik het IRIS-camerasysteem in de Maker, Edge, Pro en Ascent?

Steps to Calibrate the Joystick Open the Settings Menu On the display panel, press the gear icon in the top-right corner to open the Settings menu. Image 1: Home screen with gear icon in top-right corner Access Advanced Settings Press and hold the word “Settings” on the screen until the (...)

04/15/2026

Snelle handleiding: De joystick kalibreren voor nauwkeurige bewegingen

Door de joystick te kalibreren, kun je problemen oplossen zoals vertraagde bewegingen, onnauwkeurige besturing of het zelfstandig verschuiven van de slede in de jogmodus.

03/16/2026

Turn On To begin the laser alignment procedure, power on the laser. For the following procedures, the table will be broken into four (4) positions. Each position is identified by its relative distance to the laser source and corresponds with the mirror to adjust for that position. Three of the (...)

Laseruitlijning – Maker / Edge / Pro

Stel de spiegels van je optische systeem goed af, zodat je laser precies werkt.

Kijk even naar de bijlage voor een uitgebreide beschrijving.

Focuskalibraties – Fusion Maker, Edge en Pro

Hoe stel ik de focus in op de Fusion Maker, Fusion Edge en Fusion Pro?

This guide provides step-by-step instructions for performing precise laser alignment on the Fusion Pro CO2 and Fiber laser systems. Proper alignment ensures optimal engraving performance and reduces the risk of hardware damage. Whether you’re troubleshooting a drop in laser power or aligning after maintenance, this document will walk you through (...)

Pro 32, Pro 48

Vezeluitlijning – Fusion Pro 32 & 48

Hoe stel ik de laser in op mijn Fusion Pro Fiber- of Dual Source-machine?

Estimated time: 5 minutes • Skill: Basic Touchscreen calibration ensures accurate touch response when selecting options and settings on the display. This procedure is rarely required and should only be performed if the touchscreen is registering incorrect inputs or responding inconsistently. Touchscreen Calibration Procedure Open the Settings menu. At the (...)

Touchpad kalibreren – Fusion Maker, Edge en Pro 24 en 36

Hoe stel ik het touchpad in op de Fusion Maker, Edge en Pro 24 en 36?

01/27/2026

Fiber laser alignment is a crucial maintenance procedure to ensure the optimal performance of your Fusion Edge and Fusion Pro laser engravers. Over time, misalignment can occur due to regular use, component replacement, or moving the machine to a new location. This guide provides a step-by-step process for checking and (...)

Fiber Laser

Hoe stel ik de fiber laser de Fusion Maker, Edge en Pro 24 en 36 goed af?

This document outlines the table leveling procedure for the Fusion Maker, Edge, and Pro 24 and 36. Table level should be checked periodically to ensure that all areas of the table are the same distance from the focusing lens. If all areas of the table are not the same distance (...)

De tafel waterpas zetten

Hoe stel ik de tafel waterpas in de Fusion Maker, Edge en Pro 24 en 36?

Dit document legt uit hoe je de startpositie en de parkeerpositie kunt aanpassen voor de Fusion Maker, Fusion Edge en Fusion Pro.

De start- en parkeerposities aanpassen

Hoe stel ik de start- en parkeerposities in op de Fusion Maker, Fusion Edge en Fusion Pro?