Besturing / Printplaten

06/19/2025

This guide will walk you through the process of removing, installing, and programming the X-Axis Drive Board for Fusion Edge and Pro 24 / 36 models. Proper precautions, including the use of an anti-static strap, are essential to ensure the safe handling of electronic components. Drive Board Replacement Procedure Models: (...)

Hoe vervang je de motorbesturing van de X-as: stap voor stap uitgelegd

Leer hoe je de TE0104 X-as-aandrijfkaart vervangt op 17000 Edge- en Pro-machines. Deze reparatie kan verschillende bewegingsproblemen met de X-as oplossen en helpen om de machine weer soepel te laten werken.

11/11/2025

The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver’s (...)

Vervanging van de bedieningsmodule – Fusion Edge, Maker, Pro

04/04/2025

This document provides a step-by-step guide on how to replace the control board in your laser system. Replacing the control board is a crucial process that ensures your laser operates efficiently and reliably. Follow these instructions carefully to safely remove the old control board and install the new one, getting (...)

Vervanging van de bedieningsmodule – Fusion Pro 32 & 48

Hoe vervang ik de besturingsmodule in de Fusion Pro 32 en 48?

10/23/2025

Replacing the Control Panel Before we begin, turn off and unplug the Fusion Pro. Using a 5/32” Allen Key, remove the right side panel from the machine. Open the display panel package you received and put on the anti-static strap. Clip the strap onto any metal part of the machine. (...)

Het configuratiescherm vervangen

Zet het displaypaneel weer terug op de Fusion Pro 32 of 48.

09/24/2024

This guide provides instructions for replacing the SD card and coin battery in the control module of Fusion Pro 32 and 48 systems. Always follow proper anti-static precautions and use the correct tools and parts. Control Module Removal Turn off the engraver. Disconnect the engraver from the power source. Disconnect (...)

SD-kaart en knoopcelbatterij vervangen – Fusion Pro 32 & 48

Hoe vervang ik de SD-kaart of knoopcelbatterij in de Fusion Pro 32 en 48?

10/23/2025

Applies to: Fusion Pro 32 • Fusion Pro 48 This guide provides step-by-step instructions for upgrading the floating backplane board in Fusion Pro 32 and 48 engravers. Designed for models manufactured before mid-2020, this procedure ensures proper installation and configuration of the new backplane board. By following these instructions, you (...)

Upgrade van zwevende backplane

Hoe installeer ik de zwevende backplane in de Fusion Pro 32 en 48?

10/28/2025

Dit document legt uit hoe je de backplane-kaart in de Fusion Pro 32 en 48 vervangt.

Vervanging van de backplane-kaart – Fusion Pro 32 & 48

Hoe vervang ik de backplane-kaart in de Fusion Pro 32 en 48?

04/03/2025

This procedure outlines how to replace both the Carriage Camera PCB and the X-Axis USB-C cable on a 16000 Series Fusion Pro laser system. The Carriage Camera PCB also integrates the Auto Focus sensor, which is critical to system performance. Follow each step carefully to ensure proper installation and avoid (...)

Vervanging van lenscamera-kaart en USB-C-kabel – Fusion Pro 32 & 48

Hoe vervang ik het lenscamera-bord in de Fusion Pro 32 en 48?

04/08/2025

Dit document legt uit hoe je de printplaat van de x-as vervangt in de Fusion Maker, Edge en Pro 24 en 36.

Vervanging van de X-as-printplaat

Hoe vervang ik de printplaat van de x-as in de Fusion Maker, Edge en Pro 24 en 36?

09/24/2024

This document provides step-by-step instructions for the removal and installation of the backplane board for Fusion Pro 24 & 36 engravers. It includes all the necessary parts, tools, and materials required for the process, as well as detailed guidance on disconnecting electrical components, handling the board with care, and reassembling (...)

Vervanging van de backplane-kaart

Hoe vervang ik de backplane-kaart in de Fusion Pro 24 36?

04/08/2025

This guide provides step-by-step instructions for replacing the SD card and coin battery on Fusion Maker, Edge, and Pro systems. Be sure to follow anti-static precautions and use the required tools for each step. SD Card Replacement (Fusion Maker & Edge) Control Module / SD Card Removal Turn off the (...)

SD-kaart en knoopcelbatterij vervangen – Fusion Maker, Edge, Pro 24 & 36

Hoe vervang ik de SD-kaart en knoopcelbatterij in de Fusion Maker, Edge en Pro 24 en 36?