Service en reparatie

03/16/2026

Removal Procedure Power OFF the machine and disconnect the power cord. Remove the right and left side panels. Open the top door. Pull the rail to the middle of the machine. Move the carriage to the center. Loosen the thumb screws and open the mirror cover. Disconnect the air assist (...)

Vervanging van lineaire geleiding (IKO) – Large Aperture Fusion Pro

WARNING: Servicing the power supply while the engraver is powered on can cause serious injury or damage to internal components. Always disconnect all power sources before beginning. Power Supply Removal Power OFF the system and disconnect the power cable. Remove the rear-top panel. Disconnect all electrical harnesses from the power (...)

05/20/2025

Pro 48

Vervanging van de voeding – Fusion Pro 48 200 Watt

Stapsgewijze instructies voor het vervangen van de voeding in een Fusion Pro 48 lasersysteem.

05/19/2025

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

Autofocus-schakelaar vervangen – Fusion Maker, Edge, Pro 24 & 36

Hoe vervang ik de autofocusknop in de Fusion Maker, Edge en Pro 24 en 36?

Daily Maintenance Cleaning Remove the lens and carriage mirror. Safely detach both the lens and carriage mirror using the video guide below. Figure 1. Lens and carriage mirror removal process. Carriage Optics Removal Steps Disconnect the air tubing from the lens. Loosen the thumb screws on the carriage cover and (...)

05/07/2025

Optiek schoonmaken – Fusion Maker, Edge en Pro

In dit document wordt uitgelegd hoe je de optische onderdelen van de Fusion Maker, Edge en Pro op de juiste manier schoonmaakt.

Explanation of the Symptoms When encountering this issue, you may see something similar to the image below—here we can see the artwork in the preview thumbnail, but the artwork does not appear in the work area: However, if zoomed out, we can see that the artwork did transfer to the (...)

Mijn kunstwerk wordt niet weergegeven in het Epilog-dashboard.

Mijn kunstwerk wordt niet weergegeven in het Epilog-dashboard en de looptijd geeft 0:00 aan?

04/25/2025

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

Handmatige kalibratie van de focusmeter – Fusion Maker, Edge, Pro

Leer hoe je de handmatige focusmeter op een Fusion Maker-, Edge- of Pro-machine kunt kalibreren.

This guide will walk you through the process of removing, installing, and programming the X-Axis Drive Board for Fusion Edge and Pro 24 / 36 models. Proper precautions, including the use of an anti-static strap, are essential to ensure the safe handling of electronic components. Drive Board Replacement Procedure Models: (...)

Hoe vervang je de motorbesturing van de X-as: stap voor stap uitgelegd

Leer hoe je de TE0104 X-as-aandrijfkaart vervangt op 17000 Edge- en Pro-machines. Deze reparatie kan verschillende bewegingsproblemen met de X-as oplossen en helpen om de machine weer soepel te laten werken.

Generating machine logs enables Epilog Technical Support to gather important information about the machine, aiding in its diagnosis and troubleshooting. The process is straightforward and requires either a USB flash drive or a network-connected machine. This guide will outline the steps for generating logs. Logs can be generated one of (...)

11/11/2025

Machinelogboeken maken

Hoe maak ik de machinelogboeken aan?

04/11/2025

To ensure your CO2 laser engraver delivers optimal performance and consistent cutting quality, proper beam alignment is essential. Over time, vibration, wear, or component replacement can cause the laser beam to deviate from its intended path. This can result in reduced cutting power, inconsistent engraving, or premature wear of optics. (...)

Laseruitlijning (optica met grote opening) – Fusion Pro

Hoe stel ik de laser op mijn Fusion Pro in met optica met een grote opening?

The Fusion Pro laser system includes four (4) mirrors in total. Mirrors 1, 2, and 3 are mounted using mirror holders and feature thermal compound between the mirror and holder to ensure proper heat transfer. This compound may need to be replaced if the mirrors are removed and reinstalled multiple (...)

Vervanging van optiek met grote opening – Fusion Pro

Hoe vervang ik de optiek in mijn Fusion Pro Large Aperture-machine?

Regular cleaning of the Fusion Pro engraver will result in a longer service life of the engraver and less down time. Additionally, regular cleaning of the Fusion Pro engraver can mitigate the risk of flare-ups and other thermal events. A mild household cleaner or degreaser can be used to clean (...)

09/25/2025

Schoonmaakprocedures – Fusion Maker, Edge en Pro

Dit document legt uit hoe je de Fusion Maker, Edge en Pro-machine schoonmaakt en onderhoudt.