Service- en reparatiearchief

Y-motor vervangen

Vervang de motor die de x-as van je machine heen en weer beweegt.

Remove Right Panel Remove the right side panel by removing the 6 screws, 4 located on the side of the machine, two located on the back of the machine. Remove Old Y-Motor Open the front access door. Locate the Y-Motor on the right hand-side of the machine. Remove the spring (...)

Lees meer

09/24/2024

X-motor vervangen

Vervang de motor die de laserkop van je machine langs de x-as beweegt.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

Lees meer

04/11/2025

Hoog wattage

Een stroomprobleem oplossen: de dubbele voeding vervangen

Hoe vervang je de Helix voeding van de Mini / Helix .

Remove Back Panel Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the two power supplies. Disconnect Electrical Leads Disconnect four of the electrical leads. Disconnect the two connectors holding (...)

Lees meer

10/14/2025

Laag wattage

Een stroomprobleem oplossen: de voeding vervangen

Hoe vervang je de Mini / Helix voeding.

Remove Old Power Supply Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the power supply on the left hand side of the machine. Disconnect the three electrical leads. With (...)

Lees meer

10/14/2025

Het display/toetsenbord vervangen

Vervang het display/toetsenbord van je machine.

Remove Side Panels Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove (...)

Lees meer

04/14/2025

CO2 Tickle-instellingen

Wat zijn kietelinstellingen en hoe kan ik ze aanpassen?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

Lees meer

04/02/2025

Optiek vervangen –Helix

Hoe vervang ik de lens in mijn Helix Mini?

This guide provides step-by-step instructions for replacing the carriage, steering, and periscope optics in your laser system. Follow the outlined procedures carefully to ensure proper installation and alignment. Always handle optics with care and refer to the provided alignment links after replacement to maintain optimal performance. Replacing Carriage Optics Move (...)

Lees meer

04/03/2025

Uitgebreide handleiding voor koude start

Mijn laser is al een tijdje niet gebruikt en wil niet meer werken.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

Lees meer

04/08/2025

De tafel controleren en waterpas zetten

Als je merkt dat je Mini of Helix op bepaalde plekken niet gelijkmatig graveert of minder kracht heeft, kan het zijn dat de tafel niet goed waterpas staat. In deze handleiding leg ik uit hoe je de tafel kunt controleren en waterpas kunt zetten voor de beste prestaties.

Estimated time: 15-20 minutes • Skill: Beginner A perfectly level engraving table is essential for accurate focusing and consistent engraving results. This guide will walk you through checking and adjusting the table level on your Epilog Mini or Helix laser system. Checking Table Level Access the table. Power on the (...)

Lees meer

10/23/2025