{"id":18020,"date":"2024-09-24T00:00:00","date_gmt":"2024-09-24T06:00:00","guid":{"rendered":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/getting-started\/x-motor_zing\/"},"modified":"2025-10-14T16:40:24","modified_gmt":"2025-10-14T22:40:24","slug":"x-motor_zing","status":"publish","type":"post","link":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/","title":{"rendered":"Repairing X-Axis Motion: Replacing the X-Motor"},"content":{"rendered":"<h2 id=\"Remove-Right-Side-Panel\">Remove Right Side Panel<\/h2>\n<p>Shut off the laser and remove the power cord from the machine.<\/p>\n<p><img decoding=\"async\" title=\"Shut off the laser and remove the power cord from the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_01.jpg\" alt=\"Removing the power cord from the machine.\" \/><\/p>\n<p>Inside the machine, move the x-axis assembly to the rear of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Move the x-axis assembly to the back of the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_02.jpg\" alt=\"The x-axis assembly positioned at the back of the machine.\" \/><\/p>\n<p>Put on the anti-static strap. Clip the strap on to any metal part of the machine. Always wear the anti-static strap when handling the control board to avoid damaging the unit through static discharge.<\/p>\n<p><img decoding=\"async\" title=\"Put on the anti-static strap and clip it to the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_03.jpg\" alt=\"Clipping a wrist-mounted static strap to the exhaust port of the machine.\" \/><\/p>\n<p>Loosen the two screws on the side of the display panel.<\/p>\n<p><img decoding=\"async\" title=\"Loosen the display panel screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_04.jpg\" alt=\"Loosening the display panel captive screws.\" \/><\/p>\n<p>Grasp the two screws and pull the controller away from the engraver. A small amount of force will be required to remove the board from the machine as you disconnect the electrical connections.<\/p>\n<p><img decoding=\"async\" title=\"Pull the controller away from the engraver.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_05.jpg\" alt=\"Pulling the display panel out of the machine.\" \/><\/p>\n<p>Make sure the copper strips inside the control housing stay in place when you remove the board.<\/p>\n<p><img decoding=\"async\" title=\"Be sure the copper strips stay in place.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_06.jpg\" alt=\"A close-up of the copper strip inside the control housing.\" \/><\/p>\n<p>Next we\u2019ll remove the right side panel from the machine.<\/p>\n<p>Remove the three screws on the side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Remove the right side panel's side screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_07.jpg\" alt=\"Removing the right side panel's side screws.\" \/><\/p>\n<p>Remove the screw on the back of the machine holding on the side panel.<\/p>\n<p><img decoding=\"async\" title=\"Remove the right side panel's back screw.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_08.jpg\" alt=\"Removing the right side panel's back screw.\" \/><\/p>\n<p>Remove the right side cover by lifting up on the bottom of the cover and pulling toward you, then up.<\/p>\n<p><img decoding=\"async\" title=\"Remove the right side panel.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_09.jpg\" alt=\"Removing the ride side panel.\" \/><\/p>\n<h2 id=\"Remove-Left-Side-Panel\">Remove Left Side Panel<\/h2>\n<p>Remove the left side panel by removing the three screws on the side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Remove the left panel's screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_10.jpg\" alt=\"Removing the left panel's screws.\" \/><\/p>\n<p>Remove the screw on the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Remove the screw on the back side of the panel.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_11.jpg\" alt=\"Removing the screw on the left panel's back.\" \/><\/p>\n<p>Remove the left side panel by pulling it toward you.<\/p>\n<p><img decoding=\"async\" title=\"Remove the left side panel.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_12.jpg\" alt=\"Pulling away the machine's left side panel.\" \/><\/p>\n<h2 id=\"Remove-Old-Motor\">Remove Old Motor<\/h2>\n<p>On the belt assembly on the left side of the machine, loosen the two Phillips screws on the metal plate.<\/p>\n<p><img decoding=\"async\" title=\"Loosen the Phillips screw on the front side of the metal plate.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_13.jpg\" alt=\"Loosening the screw on the front of the metal plate.\" \/><img decoding=\"async\" title=\"Loosen the Phillips screw on the back side of the metal plate.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_14.jpg\" alt=\"Loosening the screw on the front of the metal plate.\" \/><\/p>\n<p>Push the idler bracket back toward the inside of the assembly to loosen the belt tension. Once moved, tighten the Phillips screws a little to hold the idler mount in place.<\/p>\n<p><img decoding=\"async\" title=\"While pushing the idler toward the machine, tighten the Phillips screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_15.jpg\" alt=\"Tightening the Phillips screws while pushing the idler bracket against the machine.\" \/><\/p>\n<p>Push the x-axis assembly to the front of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Push the x-axis assembly to the front of the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_16.jpg\" alt=\"The x-axis assembly being pushed to the front of the machine.\" \/><\/p>\n<p>Remove the two Phillips screws on the metal plate on the side of the x-axis motor.<\/p>\n<p><img decoding=\"async\" title=\"Remove the top screw securing the x-motor.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_17.jpg\" alt=\"Removing the top screw from the x-motor.\" \/><img decoding=\"async\" title=\"Remove the bottom screw securing the x-motor.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_18.jpg\" alt=\"Removing the bottom screw from the x-motor.\" \/><\/p>\n<p>Push the x-axis assembly to the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Push the x-axis assembly to the back of the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_19.jpg\" alt=\"The x-axis assembly being pushed to the back of the machine.\" \/><\/p>\n<p>Unclip the flex cable.<\/p>\n<p><img decoding=\"async\" title=\"Unclip the flex cable.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_20.jpg\" alt=\"Preparing to unplug the motor's flex cable.\" \/><\/p>\n<p>Disconnect the electrical connection behind the motor and set the old motor aside.<\/p>\n<p><img decoding=\"async\" title=\"Disconnect the electrical connection behind the motor and set the old motor aside.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_21.jpg\" alt=\"Preparing to unplug the motor's electrical connection.\" \/><\/p>\n<h2 id=\"Install-New-Motor\">Install New Motor<\/h2>\n<p>To install the new motor, reconnect the motor&#8217;s electrical connection and plug in the flex cable.<\/p>\n<p><img decoding=\"async\" title=\"Reconnect the motor's electrical connection.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_22.jpg\" alt=\"Preparing to plug in the moto'rs electrical connection.\" \/><img decoding=\"async\" title=\"Plug in the flex cable.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_23.jpg\" alt=\"Preparing to plug in the motor's flex cable.\" \/><\/p>\n<p>Push the x-axis assembly to the front of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Push the x-axis assembly to the front of the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_16.jpg\" alt=\"Pushing the x-axis assembly to the front of the machine.\" \/><\/p>\n<p>As you place the new motor in the opening in the x-axis, loop the belt over the x-motor pulley.<\/p>\n<p><img decoding=\"async\" title=\"Loop the belt over the x-motor's pulley.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg\" alt=\"Inserting the x-axis motor into the hole in the x-axis assembly while looping the belt over the motor's pulley.\" \/><\/p>\n<p>Install the two mounting screws on the side of the motor.<\/p>\n<p><img decoding=\"async\" title=\"Install the top mounting screw.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_25.jpg\" alt=\"Inserting the top x-motor mounting screw.\" \/><img decoding=\"async\" title=\"Install the bottom mounting screw.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_26.jpg\" alt=\"Inserting the bottom x-motor mounting screw.\" \/><\/p>\n<p>On the left side of the machine, loosen the two idler bracket screws and let the springs apply the tension to the x-axis belt. Ensure the idler bracket is square in the machine, then tighten the two screws again.<\/p>\n<p><img decoding=\"async\" title=\"Loosen the two idler bracket screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_27.jpg\" alt=\"The idler bracket before the springs have been freed.\" \/><img decoding=\"async\" title=\"Once the springs have expanded and pushed the idler bracket out, tighten the idler bracket screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_28.jpg\" alt=\"The idler bracket after the springs have been freed and the idler has moved.\" \/><\/p>\n<h2 id=\"Reattach-Left-Side-Panel\">Reattach Left Side Panel<\/h2>\n<p>Reinstall the left side panel by sliding it onto the chassis and reattaching the three screws on the side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Insert the left side panel's side screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_29.jpg\" alt=\"Screwing in one of the left panel's side screws.\" \/><\/p>\n<p>Tighten the screw on the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Tighten the screw on the back of the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_30.jpg\" alt=\"Screwing in the left side panel's back screw.\" \/><\/p>\n<h2 id=\"Reattach-Right-Side-Panel\">Reattach Right Side Panel<\/h2>\n<p>Replace the right side panel, tightening the three screws on the side of the panel.<\/p>\n<p><img decoding=\"async\" title=\"Put the right side panel back on the machine.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_31.jpg\" alt=\"Putting the right side panel back on the chassis.\" \/><img decoding=\"async\" title=\"Tighten the side panel's side screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_32.jpg\" alt=\"Tightening the side panel's side screws.\" \/><\/p>\n<p>Tighten the screw on the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"Tighten the side panel's back screw.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_33.jpg\" alt=\"Tightening the side panel's back screw.\" \/><\/p>\n<p>Slide the display unit into place, ensuring the tabs on the control unit fit into the grooves on the side of the housing. Push the display unit all the way into the slots until it is fully seated. Tighten the two screws to secure the display unit in place.<\/p>\n<p><img decoding=\"async\" title=\"Slide the display unit into place.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_34.jpg\" alt=\"Sliding the display panel back into its housing.\" \/><img decoding=\"async\" title=\"Tighten the display panel's two captive screws.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_35.jpg\" alt=\"Tightening the screws of the display panel.\" \/><\/p>\n<p>Plug the machine in and turn it on.<\/p>\n<p><img decoding=\"async\" title=\"Plug the machine in and turn it on.\" src=\"\/wp-content\/uploads\/zing_x-motor-replacement_36.jpg\" alt=\"Putting the power cord into the machine.\" \/><\/p>\n\r\n\t\t\t<div id=\"daexthefu-container\"\r\n\t\t\t\tclass=\"daexthefu-container daexthefu-layout-side-by-side daexthefu-alignment-left\"\r\n\t\t\t\tdata-post-id=\"18020\">\r\n\r\n\t\t\t\t<div class=\"daexthefu-feedback\">\r\n\t\t\t\t\t<div class=\"daexthefu-text\">\r\n\t\t\t\t\t\t<h3 class=\"daexthefu-title\">Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<div class=\"daexthefu-buttons-container\">\r\n\t\t\t\t\t\t<div class=\"daexthefu-buttons\">\r\n\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-yes daexthefu-button daexthefu-button-type-text\" data-value=\"1\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">Yes<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-no daexthefu-button daexthefu-button-type-text\" data-value=\"0\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">No<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-comment\">\r\n\t\t\t\t\t<div class=\"daexthefu-comment-top-container\">\r\n\t\t\t\t\t\t<label id=\"daexthefu-comment-label\" class=\"daexthefu-comment-label\"><\/label>\r\n\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-container\">\r\n\t\t\t\t\t\t\t\t<div id=\"daexthefu-comment-character-counter-number\"\r\n\t\t\t\t\t\t\t\t\tclass=\"daexthefu-comment-character-counter-number\"><\/div>\r\n\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-text\"><\/div>\r\n\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<textarea id=\"daexthefu-comment-textarea\" class=\"daexthefu-comment-textarea\"\r\n\t\t\t\t\t\t\t\tplaceholder=\"Type your message\"\r\n\t\t\t\t\t\t\t\tmaxlength=\"\r\n\t\t\t\t\t\t\t\t400\t\t\t\t\t\t\t\t\t\"><\/textarea>\r\n\t\t\t\t\t<div class=\"daexthefu-comment-buttons-container\">\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-submit daexthefu-button\">Submit<\/button>\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-cancel daexthefu-button\">Cancel<\/button>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-successful-submission-text\">Thanks for your feedback!<\/div>\r\n\r\n\t\t\t<\/div>\r\n\r\n\t\t\t","protected":false},"excerpt":{"rendered":"<p>Remove Right Side Panel Shut off the laser and remove the power cord from the machine. Inside the machine, move the x-axis assembly to the rear of the machine. Put on the anti-static strap. Clip the strap on to any metal part of the machine. Always wear the anti-static strap when handling the control board [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":4754,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_helpful_status":1,"_helpful_pro_status":1,"footnotes":""},"categories":[557,558],"tags":[],"laser_machine":[70],"post_folder":[],"class_list":["post-18020","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-service-and-repair","category-x-axis","laser_machine-zing"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v27.0 (Yoast SEO v27.8) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Repairing X-Axis Motion: Replacing the X-Motor - Epilog Support Center<\/title>\n<meta name=\"description\" content=\"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Repairing X-Axis Motion: Replacing the X-Motor\" \/>\n<meta property=\"og:description\" content=\"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/\" \/>\n<meta property=\"og:site_name\" content=\"Epilog Support Center\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/epiloglaser\" \/>\n<meta property=\"article:published_time\" content=\"2024-09-24T06:00:00+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2025-10-14T22:40:24+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"830\" \/>\n\t<meta property=\"og:image:height\" content=\"467\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Billy\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:site\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Billy\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"10 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/\"},\"author\":{\"name\":\"Billy\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/62709b908d1b2e3cef3756c590032c9b\"},\"headline\":\"Repairing X-Axis Motion: Replacing the X-Motor\",\"datePublished\":\"2024-09-24T06:00:00+00:00\",\"dateModified\":\"2025-10-14T22:40:24+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/\"},\"wordCount\":550,\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/zing_x-motor-replacement_24.jpg\",\"articleSection\":[\"Service and Repair\",\"X-Axis\"],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/\",\"name\":\"Repairing X-Axis Motion: Replacing the X-Motor - Epilog Support Center\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/zing_x-motor-replacement_24.jpg\",\"datePublished\":\"2024-09-24T06:00:00+00:00\",\"dateModified\":\"2025-10-14T22:40:24+00:00\",\"description\":\"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#primaryimage\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/zing_x-motor-replacement_24.jpg\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/zing_x-motor-replacement_24.jpg\",\"width\":830,\"height\":467},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/zing\\\/service-and-repair\\\/x-motor_zing\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Repairing X-Axis Motion: Replacing the X-Motor\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"name\":\"Epilog Support Center\",\"description\":\"Imagine. Design. Create.\",\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\",\"name\":\"Epilog Laser\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"width\":215,\"height\":46,\"caption\":\"Epilog Laser\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/epiloglaser\",\"https:\\\/\\\/x.com\\\/epiloglaser\",\"https:\\\/\\\/www.instagram.com\\\/epiloglaser\\\/\",\"https:\\\/\\\/www.youtube.com\\\/@epiloglaser\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/epilog\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/62709b908d1b2e3cef3756c590032c9b\",\"name\":\"Billy\",\"sameAs\":[\"https:\\\/\\\/support.epiloglaser.com\\\/staging\"],\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/author\\\/kbtest\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Repairing X-Axis Motion: Replacing the X-Motor - Epilog Support Center","description":"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/","og_locale":"en_US","og_type":"article","og_title":"Repairing X-Axis Motion: Replacing the X-Motor","og_description":"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.","og_url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/","og_site_name":"Epilog Support Center","article_publisher":"https:\/\/www.facebook.com\/epiloglaser","article_published_time":"2024-09-24T06:00:00+00:00","article_modified_time":"2025-10-14T22:40:24+00:00","og_image":[{"width":830,"height":467,"url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg","type":"image\/jpeg"}],"author":"Billy","twitter_card":"summary_large_image","twitter_creator":"@epiloglaser","twitter_site":"@epiloglaser","twitter_misc":{"Written by":"Billy","Est. reading time":"10 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#article","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/"},"author":{"name":"Billy","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/62709b908d1b2e3cef3756c590032c9b"},"headline":"Repairing X-Axis Motion: Replacing the X-Motor","datePublished":"2024-09-24T06:00:00+00:00","dateModified":"2025-10-14T22:40:24+00:00","mainEntityOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/"},"wordCount":550,"publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg","articleSection":["Service and Repair","X-Axis"],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/","url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/","name":"Repairing X-Axis Motion: Replacing the X-Motor - Epilog Support Center","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#website"},"primaryImageOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#primaryimage"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg","datePublished":"2024-09-24T06:00:00+00:00","dateModified":"2025-10-14T22:40:24+00:00","description":"Step-by-step guide for replacing the X-Axis motor in an Epilog Zing laser engraving machine.","breadcrumb":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#primaryimage","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/zing_x-motor-replacement_24.jpg","width":830,"height":467},{"@type":"BreadcrumbList","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/service-and-repair\/x-motor_zing\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/support.epiloglaser.com\/staging\/"},{"@type":"ListItem","position":2,"name":"Repairing X-Axis Motion: Replacing the X-Motor"}]},{"@type":"WebSite","@id":"https:\/\/support.epiloglaser.com\/staging\/#website","url":"https:\/\/support.epiloglaser.com\/staging\/","name":"Epilog Support Center","description":"Imagine. Design. Create.","publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/support.epiloglaser.com\/staging\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/support.epiloglaser.com\/staging\/#organization","name":"Epilog Laser","url":"https:\/\/support.epiloglaser.com\/staging\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","width":215,"height":46,"caption":"Epilog Laser"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/epiloglaser","https:\/\/x.com\/epiloglaser","https:\/\/www.instagram.com\/epiloglaser\/","https:\/\/www.youtube.com\/@epiloglaser","https:\/\/www.linkedin.com\/company\/epilog"]},{"@type":"Person","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/62709b908d1b2e3cef3756c590032c9b","name":"Billy","sameAs":["https:\/\/support.epiloglaser.com\/staging"],"url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/author\/kbtest\/"}]}},"_links":{"self":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18020","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/comments?post=18020"}],"version-history":[{"count":2,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18020\/revisions"}],"predecessor-version":[{"id":20824,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18020\/revisions\/20824"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media\/4754"}],"wp:attachment":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media?parent=18020"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/categories?post=18020"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/tags?post=18020"},{"taxonomy":"laser_machine","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/laser_machine?post=18020"},{"taxonomy":"post_folder","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/post_folder?post=18020"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}