{"id":18029,"date":"2024-09-24T00:00:00","date_gmt":"2024-09-24T06:00:00","guid":{"rendered":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/getting-started\/y-axis-assembly_fusion\/"},"modified":"2024-09-24T00:00:00","modified_gmt":"2024-09-24T06:00:00","slug":"y-axis-assembly_fusion","status":"publish","type":"post","link":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/","title":{"rendered":"Y-Axis Assembly"},"content":{"rendered":"<h2 id=\"Remove-Panels\">Remove Panels<\/h2>\n<p>Shut off the laser and remove the power cord from the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_01.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_02.jpg\" alt=\"\" \/><\/p>\n<p>We\u2019ll begin by replacing the y-axis on the right-hand side of the machine.<\/p>\n<p>Use a 5\/32\u201d hex key to remove the exhaust plenum on the rear of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_03.jpg\" alt=\"\" \/><\/p>\n<p>Then remove the small panel in the top left corner.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_04.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_05.jpg\" alt=\"\" \/><\/p>\n<p>Next use a 5\/32\u201d hex key to remove the top access panel on the left side of the machine, as well as both the top and bottom access panels on the right side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_06.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_07.jpg\" alt=\"\" \/><\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_08.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_09.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Remove-X_Axis-Assembly\">Remove X-Axis Assembly<\/h2>\n<p>On the left side of the machine, find and disconnect the Air Assist tube from the x-axis assembly. Press the ring toward the rear of the engraver while pulling on the black tube.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_10.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_11.jpg\" alt=\"\" \/><\/p>\n<p>The wire harness and its plastic guard are held secure by the wire harness clamp. With a short or offset Philips head screw driver remove the clamp screws then set the clamp aside.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_12.jpg\" alt=\"\" \/><\/p>\n<p>Disconnect the white connector from its socket by squeezing the lock tab on the bottom of the connector and pulling it away from the circuit board. Remove the black connector as well.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_13.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_14.jpg\" alt=\"\" \/><\/p>\n<p>Then remove the lens assembly by loosening the 3 thumb screws on its front face until they spin freely. They are captive screws and will not come out of the assembly.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_15.jpg\" alt=\"\" \/><\/p>\n<p>Slide the assembly out of its housing and set it aside.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_16.jpg\" alt=\"\" \/><\/p>\n<p>Now it\u2019s time to remove the x-axis assembly.<\/p>\n<p>On both ends of the assembly, loosen the 2 green captive screws until they turn freely.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_17.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_18.jpg\" alt=\"\" \/><\/p>\n<p>Now carefully lift the assembly from its mounted position and carry it out through the right side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_19.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_20.jpg\" alt=\"\" \/><\/p>\n<p>We will begin by replacing the <em>right-side<\/em> Y-Axis components. If you only need to replace the <em>left-side<\/em> components, skip ahead to <a href=\"#removeadditionalpanels-fusion\">Remove Additional Panels<\/a><\/p>\n<h2 id=\"Remove-Right-Y_Axis\">Remove Old Right Y-Axis<\/h2>\n<p>Use a nut driver to remove the 2 nuts securing the compartment panels on the interior side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_21.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to remove the 3 screws securing the top of the compartment to the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_22.jpg\" alt=\"\" \/><\/p>\n<p>Then use a Philips head screwdriver to remove the 2 screws securing the compartment panels from underneath.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_23.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_24.jpg\" alt=\"\" \/><\/p>\n<p>Gently pull out the compartment panels and let them rest, hanging off the side of the chassis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_25.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_26.jpg\" alt=\"\" \/><\/p>\n<p>On the back side of the machine use a 5\/32\u201d hex key to loosen the 2 hex screws securing the axle clamp to the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_27.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/32\u201d hex key to loosen but not remove the four mounting screws located at each corner of the y-motor.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_28.jpg\" alt=\"\" \/><\/p>\n<p>From the right-hand side of the machine use a pencil to mark the top of the y-motor mounting bracket. This will be used as a guide to return the mounting bracket to the correct position later.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_29.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/32\u201d hex key to loosen the y-motor tensioning screw. This will loosen the y-axis reducer drive belt.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_30.jpg\" alt=\"\" \/><\/p>\n<p>Remove the reducer drive belt from the y-motor pulley.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_31.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_32.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/32\u201d hex key to remove the two hex keys securing the y-axis to the chassis near the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_33.jpg\" alt=\"\" \/><\/p>\n<p>Remove the black plastic shim underneath the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_34.jpg\" alt=\"\" \/><\/p>\n<p>Then remove the two hex screws securing the y-axis to the chassis near the front of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_35.jpg\" alt=\"\" \/><\/p>\n<p>Remove the black plastic shim.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_36.jpg\" alt=\"\" \/><\/p>\n<p>Now remove the y-axis. Carefully lift it, turning it 90 degrees inward while lifting the back up and leaning the front down.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_37.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_38.jpg\" alt=\"\" \/><\/p>\n<p>Push it slightly out the back through the open corner panel, then pull the entire axis out through the side of the compartment<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_39.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_40.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Install-Right-Y_Axis\">Install New Right Y-Axis<\/h2>\n<p>To install the new y-axis begin by holding it so the wheel is positioned on top.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_41.jpg\" alt=\"\" \/><\/p>\n<p>Slide it in through the side of the compartment, pushing the back end with the wheel out through the top corner panel on the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_42.jpg\" alt=\"\" \/><\/p>\n<p>When the front end is within the chassis, straighten it out then turn the axis 90 degrees outward and rest it on its mounting brackets.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_43.jpg\" alt=\"\" \/><\/p>\n<p>Insert the y-axis drive axle into the rear axle clamp.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_44.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_45.jpg\" alt=\"\" \/><\/p>\n<p>Secure the front of the y-axis to its mounting bracket by using a 5\/32\u201d hex key to insert the two hex screws halfway so that the y-axis can still be lifted slightly.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_46.jpg\" alt=\"\" \/><\/p>\n<p>Lift the y-axis and insert the black plastic shim, then tighten the 2 hex screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_47.jpg\" alt=\"\" \/><\/p>\n<p>Secure the back of the y-axis to its mounting bracket the same way, using a 5\/32\u201d hex key to insert the 2 hex screws halfway.<\/p>\n<p>Insert the black plastic shim, then tighten the 2 hex screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_48.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_49.jpg\" alt=\"\" \/><\/p>\n<p>Slide the drive belt onto the two wheels.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_50.jpg\" alt=\"\" \/><\/p>\n<p>Tighten the y-motor tensioning screw until the pencil mark you made earlier is visible.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_51.jpg\" alt=\"\" \/><\/p>\n<p>Now tighten the 4 mounting screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_52.jpg\" alt=\"\" \/><\/p>\n<p>Now lift the compartment panels and slide them back into place over the two mounting screws on the interior side of the compartment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_53.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_54.jpg\" alt=\"\" \/><\/p>\n<p>Insert the two Philips head screws from underneath.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_55.jpg\" alt=\"\" \/><\/p>\n<p>Then use a Philips head screwdriver to insert the 3 screws that connect the compartment panels to the side of the y axis. Two of the screws will also go through and secure the wire harness clamps.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_56.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_57.jpg\" alt=\"\" \/><\/p>\n<p>We will now replace the <em>left-side<\/em> Y-Axis components. If you do not need to do this, skip ahead to <a href=\"#alignandclamp-fusion\">Align and Clamp<\/a><\/p>\n<h2 id=\"Remove-Additional-Panels\">Remove Additional Panels<\/h2>\n<p>Now we\u2019ll replace the y-axis on the left side of the machine.<\/p>\n<p>Use a 5\/32\u201d hex key to remove the bottom access panel on the left side of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_58.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_59.jpg\" alt=\"\" \/><\/p>\n<p>Then, while facing the back of the machine, remove the small panel on the right, near the edge.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_60.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Remove-Left-Y_Axis\">Remove Old Left Y-Axis<\/h2>\n<p>Use a 5\/32\u201d hex key to loosen the 2 hex screws securing the axle clamp on the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_61.jpg\" alt=\"\" \/><\/p>\n<p>Then use a Philips head screwdriver to remove the 3 screws securing the compartment panels to the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_62.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to remove the 2 screws securing the compartment panels from underneath.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_63.jpg\" alt=\"\" \/><\/p>\n<p>If your Fusion M2 is equipped with a fiber laser source, you will need to remove the fiber laser head to provide clearance for the compartment panels to be removed. Use a 5\/32\u201d hex key to remove the 4 hex screws securing the laser head clamp.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_64.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_65.jpg\" alt=\"\" \/><\/p>\n<p>Set the laser head to the side so it\u2019s out of the path of the compartment panels.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_66.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to remove the 2 screws securing the front sensor to the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_67.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_68.jpg\" alt=\"\" \/><\/p>\n<p>Set the small metal switch guard to the side.<\/p>\n<p>Gently pull out the compartment panels and let them rest, hanging off the side of the chassis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_69.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_70.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to remove the 2 screws securing the rear sensor to the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_71.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_72.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/32\u201d hex key to remove the 2 hex screws securing the y-axis to the chassis near the back of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_73.jpg\" alt=\"\" \/><\/p>\n<p>Remove the black plastic shim.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_74.jpg\" alt=\"\" \/><\/p>\n<p>Then remove the 2 hex screws securing the y-axis to the chassis near the front of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_75.jpg\" alt=\"\" \/><\/p>\n<p>Remove the black plastic shim.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_76.jpg\" alt=\"\" \/><\/p>\n<p>Manually loosen the black plastic screw near the bottom of the periscope.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_77.jpg\" alt=\"\" \/><\/p>\n<p>From the top compartment pull the metal tube out and set it aside.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_78.jpg\" alt=\"\" \/><\/p>\n<p>Now remove the y-axis, rotating it 90 degrees outward while dropping it down and around the mounting brackets.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_79.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_80.jpg\" alt=\"\" \/><\/p>\n<p>Push it slightly out the back through the open panel, then pull the entire axis out through the side of the compartment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_81.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_82.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Install-Left-Y_Axis\">Install New Left Y-Axis<\/h2>\n<p>To install the new y-axis put the rear end of the axis into the machine with the axle pointing outward, push it slightly through the back open panel, then pull it forward into the machine, rotate it 180 degrees inward as you bring it up and over to rest on top of the brackets.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_83.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_84.jpg\" alt=\"\" \/><\/p>\n<p>Slide the y-axis axle into the clamp in the rear of the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_85.jpg\" alt=\"\" \/><\/p>\n<p>Secure the front of the y-axis to its mounting bracket by using a 5\/32\u201d hex key to insert the two hex screws halfway so that the y-axis can still be lifted slightly.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_86.jpg\" alt=\"\" \/><\/p>\n<p>Lift the y-axis and insert the black plastic shim, then tighten the 2 hex screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_87.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_88.jpg\" alt=\"\" \/><\/p>\n<p>Secure the back of the y-axis to its mounting bracket the same way, using a 5\/32\u201d hex key to insert the 2 hex screws halfway.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_89.jpg\" alt=\"\" \/><\/p>\n<p>Insert the black plastic shim, then tighten the 2 hex screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_90.jpg\" alt=\"\" \/><\/p>\n<p>From the top compartment slide the metal periscope tube back into the housing in the bottom compartment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_91.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_92.jpg\" alt=\"\" \/><\/p>\n<p>Lift the tube up into the housing at the top, then manually tighten the black mounting screw at the bottom.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_93.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_94.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to insert the 2 screws that secure the rear axis sensor and switch guard to the side of the y-axis. Be sure to affix the switch guard on the sensor\u2019s right side.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_95.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_96.jpg\" alt=\"\" \/><\/p>\n<p>Now lift the compartment panel and slide it back into place over the 2 mounting screws on the interior side of the compartment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_97.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_98.jpg\" alt=\"\" \/><\/p>\n<p>Insert the 2 Philips head screws from underneath.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_99.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_100.jpg\" alt=\"\" \/><\/p>\n<p>Use a Philips head screwdriver to insert the 3 screws that connect the compartment panels to the side of the y-axis.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_101.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_102.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/16\u201d nut driver to secure the 2 nuts over the 2 mounting screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_103.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_104.jpg\" alt=\"\" \/><\/p>\n<p>Then use a Philips head screwdriver to insert the 2 screws that secure the front y-axis sensor and switch guard to the side of the y-axis. Be sure to affix the switch guard to the sensor\u2019s left side.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_105.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_106.jpg\" alt=\"\" \/><\/p>\n<p>Now put the laser head back on the mount near the rear of the compartment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_107.jpg\" alt=\"\" \/><\/p>\n<p>Using a 5\/32\u201d hex key insert the 4 hex screws to secure the clamp around the laser head. Be sure to create a good seal by gently pressing the laser head against the back felt pad.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_108.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_109.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Align-and-Clamp\">Align and Clamp<\/h2>\n<p>Move the Y-Axis Assembly on either side of the machine as far back to the rear as they can go. This will ensure the two sides are in alignment.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_110.jpg\" alt=\"\" \/><\/p>\n<p>Use a 5\/32&#8243; hex key to secure the clamp screws on the rear axle. There are 2 clamp screws on either side of the machine. Be sure to secure any that you loosened earlier in the process.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_111.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_112.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Replace-X_Axis-Assembly\">Replace X-Axis Assembly<\/h2>\n<p>Place the x-axis assembly back onto its mountings and secure it by tightening its 4 green captive screws, lining it up with the guide pins so there is no space between the bottom of the assembly and the screw mounts.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_114.jpg\" alt=\"\" \/><\/p>\n<p>Use a short or offset Philips head screwdriver to tighten the green captive screws on both sides.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_115.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_116.jpg\" alt=\"\" \/><\/p>\n<p>Next connect the wire harness by plugging in the black connector then the white connector.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_117.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_118.jpg\" alt=\"\" \/><\/p>\n<p>Retrieve the wire harness clamp and position the wire harness and its plastic guard so that the harness is on top of the guard and both are under the clamp on the x-axis assembly.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_119.jpg\" alt=\"\" \/><\/p>\n<p>Be sure that the wires between the wire harness and the circuit board have some slack and are not drawn too tight. Secure the clamp by inserting the two screws.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_120.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_121.jpg\" alt=\"\" \/><\/p>\n<p>Reinsert the air assist tube on the left end of the assembly. The ring will pop out once the tube is successfully inserted.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_122.jpg\" alt=\"\" \/><\/p>\n<p>Reinstall the lens assembly by sliding it into the housing and tightening the 3 screws on its front face.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_123.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_124.jpg\" alt=\"\" \/><\/p>\n<h2 id=\"Reinstall-Panels\">Reinstall Panels<\/h2>\n<p>Now use a 5\/32\u201d hex key to reattach all of the panels on the machine.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_125.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_126.jpg\" alt=\"\" \/><\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_127.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_128.jpg\" alt=\"\" \/><\/p>\n<p>Then plug the machine in and turn it on.<\/p>\n<p><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_129.jpg\" alt=\"\" \/><img decoding=\"async\" title=\"\" src=\"\/wp-content\/uploads\/fusion_y-axis-assembly_130.jpg\" alt=\"\" \/><\/p>\n\r\n\t\t\t<div id=\"daexthefu-container\"\r\n\t\t\t\tclass=\"daexthefu-container daexthefu-layout-side-by-side daexthefu-alignment-left\"\r\n\t\t\t\tdata-post-id=\"18029\">\r\n\r\n\t\t\t\t<div class=\"daexthefu-feedback\">\r\n\t\t\t\t\t<div class=\"daexthefu-text\">\r\n\t\t\t\t\t\t<h3 class=\"daexthefu-title\">Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<div class=\"daexthefu-buttons-container\">\r\n\t\t\t\t\t\t<div class=\"daexthefu-buttons\">\r\n\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-yes daexthefu-button daexthefu-button-type-text\" data-value=\"1\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">Yes<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-no daexthefu-button daexthefu-button-type-text\" data-value=\"0\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">No<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-comment\">\r\n\t\t\t\t\t<div class=\"daexthefu-comment-top-container\">\r\n\t\t\t\t\t\t<label id=\"daexthefu-comment-label\" class=\"daexthefu-comment-label\"><\/label>\r\n\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-container\">\r\n\t\t\t\t\t\t\t\t<div id=\"daexthefu-comment-character-counter-number\"\r\n\t\t\t\t\t\t\t\t\tclass=\"daexthefu-comment-character-counter-number\"><\/div>\r\n\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-text\"><\/div>\r\n\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<textarea id=\"daexthefu-comment-textarea\" class=\"daexthefu-comment-textarea\"\r\n\t\t\t\t\t\t\t\tplaceholder=\"Type your message\"\r\n\t\t\t\t\t\t\t\tmaxlength=\"\r\n\t\t\t\t\t\t\t\t400\t\t\t\t\t\t\t\t\t\"><\/textarea>\r\n\t\t\t\t\t<div class=\"daexthefu-comment-buttons-container\">\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-submit daexthefu-button\">Submit<\/button>\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-cancel daexthefu-button\">Cancel<\/button>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-successful-submission-text\">Thanks for your feedback!<\/div>\r\n\r\n\t\t\t<\/div>\r\n\r\n\t\t\t","protected":false},"excerpt":{"rendered":"<p>Remove Panels Shut off the laser and remove the power cord from the machine. We\u2019ll begin by replacing the y-axis on the right-hand side of the machine. Use a 5\/32\u201d hex key to remove the exhaust plenum on the rear of the machine. Then remove the small panel in the top left corner. Next use [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":4792,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_helpful_status":1,"_helpful_pro_status":1,"footnotes":""},"categories":[557,564],"tags":[],"laser_machine":[72],"post_folder":[],"class_list":["post-18029","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-service-and-repair","category-y-axis","laser_machine-fusion-m2"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v27.0 (Yoast SEO v27.8) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Y-Axis Assembly - Epilog Support Center<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Y-Axis Assembly\" \/>\n<meta property=\"og:description\" content=\"Remove Panels Shut off the laser and remove the power cord from the machine. We\u2019ll begin by replacing the y-axis on the right-hand side of the machine. Use a 5\/32\u201d hex key to remove the exhaust plenum on the rear of the machine. Then remove the small panel in the top left corner. Next use [&hellip;]\" \/>\n<meta property=\"og:url\" content=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/\" \/>\n<meta property=\"og:site_name\" content=\"Epilog Support Center\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/epiloglaser\" \/>\n<meta property=\"article:published_time\" content=\"2024-09-24T06:00:00+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"830\" \/>\n\t<meta property=\"og:image:height\" content=\"467\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Billy\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:site\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Billy\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/\"},\"author\":{\"name\":\"Billy\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/62709b908d1b2e3cef3756c590032c9b\"},\"headline\":\"Y-Axis Assembly\",\"datePublished\":\"2024-09-24T06:00:00+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/\"},\"wordCount\":1832,\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/fusion_y-axis-assembly_113.jpg\",\"articleSection\":[\"Service and Repair\",\"Y-Axis\"],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/\",\"name\":\"Y-Axis Assembly - Epilog Support Center\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/fusion_y-axis-assembly_113.jpg\",\"datePublished\":\"2024-09-24T06:00:00+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#primaryimage\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/fusion_y-axis-assembly_113.jpg\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/fusion_y-axis-assembly_113.jpg\",\"width\":830,\"height\":467},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-m2\\\/service-and-repair\\\/y-axis-assembly_fusion\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Y-Axis Assembly\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"name\":\"Epilog Support Center\",\"description\":\"Imagine. Design. Create.\",\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\",\"name\":\"Epilog Laser\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"width\":215,\"height\":46,\"caption\":\"Epilog Laser\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/epiloglaser\",\"https:\\\/\\\/x.com\\\/epiloglaser\",\"https:\\\/\\\/www.instagram.com\\\/epiloglaser\\\/\",\"https:\\\/\\\/www.youtube.com\\\/@epiloglaser\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/epilog\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/62709b908d1b2e3cef3756c590032c9b\",\"name\":\"Billy\",\"sameAs\":[\"https:\\\/\\\/support.epiloglaser.com\\\/staging\"],\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/author\\\/kbtest\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Y-Axis Assembly - Epilog Support Center","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/","og_locale":"en_US","og_type":"article","og_title":"Y-Axis Assembly","og_description":"Remove Panels Shut off the laser and remove the power cord from the machine. We\u2019ll begin by replacing the y-axis on the right-hand side of the machine. Use a 5\/32\u201d hex key to remove the exhaust plenum on the rear of the machine. Then remove the small panel in the top left corner. Next use [&hellip;]","og_url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/","og_site_name":"Epilog Support Center","article_publisher":"https:\/\/www.facebook.com\/epiloglaser","article_published_time":"2024-09-24T06:00:00+00:00","og_image":[{"width":830,"height":467,"url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg","type":"image\/jpeg"}],"author":"Billy","twitter_card":"summary_large_image","twitter_creator":"@epiloglaser","twitter_site":"@epiloglaser","twitter_misc":{"Written by":"Billy","Est. reading time":"9 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#article","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/"},"author":{"name":"Billy","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/62709b908d1b2e3cef3756c590032c9b"},"headline":"Y-Axis Assembly","datePublished":"2024-09-24T06:00:00+00:00","mainEntityOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/"},"wordCount":1832,"publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg","articleSection":["Service and Repair","Y-Axis"],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/","url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/","name":"Y-Axis Assembly - Epilog Support Center","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#website"},"primaryImageOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#primaryimage"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg","datePublished":"2024-09-24T06:00:00+00:00","breadcrumb":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#primaryimage","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/fusion_y-axis-assembly_113.jpg","width":830,"height":467},{"@type":"BreadcrumbList","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-m2\/service-and-repair\/y-axis-assembly_fusion\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/support.epiloglaser.com\/staging\/"},{"@type":"ListItem","position":2,"name":"Y-Axis Assembly"}]},{"@type":"WebSite","@id":"https:\/\/support.epiloglaser.com\/staging\/#website","url":"https:\/\/support.epiloglaser.com\/staging\/","name":"Epilog Support Center","description":"Imagine. Design. Create.","publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/support.epiloglaser.com\/staging\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/support.epiloglaser.com\/staging\/#organization","name":"Epilog Laser","url":"https:\/\/support.epiloglaser.com\/staging\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","width":215,"height":46,"caption":"Epilog Laser"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/epiloglaser","https:\/\/x.com\/epiloglaser","https:\/\/www.instagram.com\/epiloglaser\/","https:\/\/www.youtube.com\/@epiloglaser","https:\/\/www.linkedin.com\/company\/epilog"]},{"@type":"Person","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/62709b908d1b2e3cef3756c590032c9b","name":"Billy","sameAs":["https:\/\/support.epiloglaser.com\/staging"],"url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/author\/kbtest\/"}]}},"_links":{"self":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18029","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/comments?post=18029"}],"version-history":[{"count":0,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18029\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media\/4792"}],"wp:attachment":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media?parent=18029"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/categories?post=18029"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/tags?post=18029"},{"taxonomy":"laser_machine","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/laser_machine?post=18029"},{"taxonomy":"post_folder","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/post_folder?post=18029"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}