{"id":18084,"date":"2024-09-24T00:00:00","date_gmt":"2024-09-24T06:00:00","guid":{"rendered":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/getting-started\/sd-card-and-coin-battery-replacement-fusion-pro-32-48\/"},"modified":"2025-10-23T13:18:19","modified_gmt":"2025-10-23T19:18:19","slug":"sd-card-and-coin-battery-replacement-fusion-pro-32-48","status":"publish","type":"post","link":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/sd-card-and-coin-battery-replacement-fusion-pro-32-48\/","title":{"rendered":"SD Card and Coin Battery Replacement – Fusion Pro 32 & 48"},"content":{"rendered":"

\n This guide provides instructions for replacing the SD card and coin battery in the control module of Fusion Pro 32 and 48 systems. Always follow proper anti-static precautions and use the correct tools and parts.\n<\/p>\n

Control Module Removal<\/h2>\n
    \n
  1. Turn off the engraver.<\/li>\n
  2. Disconnect the engraver from the power source.<\/li>\n
  3. Disconnect all cables (USB, Ethernet, fan control, etc.).<\/li>\n
  4. Put on the anti-static strap and attach it to a bare metal surface on the machine.<\/li>\n
  5. Loosen the two Phillips screws on the control module.
    \n\t \"Control<\/li>\n
  6. Grip the screws and gently pull the module straight out, keeping it parallel with the engraver.
    \n \"Control<\/p>\n
    \n

    The control module slides into tracks on both sides of the housing.<\/p>\n

    Do not lift or tilt<\/strong> the module during removal or installation. Slide it straight in or out, parallel to the top of the engraver.<\/p>\n<\/div>\n

    \"Control\n <\/li>\n<\/ol>\n

    SD Card Replacement<\/h2>\n
      \n
    1. Wear your anti-static strap and attach it to a metal surface.<\/li>\n
    2. Place the control module face-down on a soft surface.<\/li>\n
    3. Locate the SD card holder on the underside of the module.
      \n \"SD\n <\/li>\n
    4. Slide the SD card out.
      \n\t \"SD<\/li>\n
    5. Insert the new SD card with copper terminals facing the control board.
      \n\t \"SD<\/li>\n<\/ol>\n

      Coin Battery Replacement<\/h2>\n
        \n
      1. Wear your anti-static strap and attach it to a metal surface.<\/li>\n
      2. Place the control module face-down on a soft surface.<\/li>\n
      3. Locate the coin battery holder.
        \n \"Battery\n <\/li>\n
      4. Remove the old battery.
        \n\t \"Battery<\/li>\n
      5. Insert the new battery with the positive terminal facing away from the control board.
        \n\t \"Battery<\/li>\n<\/ol>\n

        Control Module Reinstallation<\/h2>\n
          \n
        1. Wear your anti-static strap and attach it to the machine.<\/li>\n
        2. Align the control module with the left and right housing tracks.
          \n \"Aligning\n <\/li>\n
        3. Slide the control module back into place gently.
          \n\t \"control<\/li>\n
        4. Tighten the two Phillips screws.
          \n\t \"control<\/li>\n
        5. Reconnect to power and turn on the engraver.<\/li>\n<\/ol>\n

          Programming Peripherals<\/h2>\n
          \n Note:<\/strong> If your machine is running firmware version 1.1.2.x or later, please skip this section.\n<\/div>\n
            \n
          1. \n

            At the display panel, press the gear icon in the upper-right corner to open the Settings<\/strong> menu.<\/p>\n

            \"Accessing\n <\/li>\n

          2. \n

            Press Update<\/strong>.<\/p>\n

            \"Selecting\n <\/li>\n

          3. \n

            Press Program Peripherals<\/strong>.<\/p>\n

            \"Navigating\n <\/li>\n

          4. \n

            Once in the Peripheral Update<\/strong> menu, select All Available Peripherals<\/strong> and press Update<\/strong>.<\/p>\n

            \"Selecting\n <\/li>\n

          5. \n

            Allow the engraver to complete the update process.<\/p>\n

            \n

            Warning:<\/strong> Do not power off the engraver during the update. The screen may go dark temporarily\u2014this is normal. Once the update is complete, the system will prompt you to restart the engraver.<\/p>\n<\/p><\/div>\n<\/li>\n

          6. \n

            When prompted, power cycle the engraver to complete the update.<\/p>\n

            \"Power\n <\/li>\n<\/ol>\n\r\n\t\t\t

            \r\n\r\n\t\t\t\t
            \r\n\t\t\t\t\t
            \r\n\t\t\t\t\t\t

            Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t
            \r\n\t\t\t\t\t\t
            \r\n\t\t\t\t\t\t\t\r\n\t\t\t
            \r\n\t\t\t\t
            Yes<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t\t\r\n\t\t\t
            \r\n\t\t\t\t
            No<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t
            \r\n\t\t\t\t\t
            \r\n\t\t\t\t\t\t