{"id":18831,"date":"2025-04-04T11:20:42","date_gmt":"2025-04-04T17:20:42","guid":{"rendered":"https:\/\/support.epiloglaser.com\/staging\/?p=18831"},"modified":"2025-04-04T11:46:42","modified_gmt":"2025-04-04T17:46:42","slug":"control-module-replacement-fusion-edge-maker-pro","status":"publish","type":"post","link":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-edge\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/","title":{"rendered":"Control Module Replacement &#8211; Fusion Edge, Maker, Pro"},"content":{"rendered":"<p>The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver&#8217;s efficiency and longevity.<\/p>\n<h2>Control Module Removal (Fusion Maker &#038; Edge)<\/h2>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>Turn off the engraver.<\/li>\n<li>Disconnect engraver from power source.<\/li>\n<li>Disconnect the connection cables (USB, ethernet, fan control, etc.).<\/li>\n<li>Remove the right panel of the engraver.<\/li>\n<li>Attach the anti-static strap to your wrist and clamp it to a bare metal surface.<\/li>\n<li>\n<p>Loosen and remove the four (4) 5\/32\u201d Allen screws on the control module.<\/p>\n<p>\t\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_001.png\" alt= \"control panel screws\"><\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-primary uk-h4\"><i class=\"fas fa-exclamation-circle uk-margin-small-right\"><\/i>Note: <\/span><\/strong>Two (2) of the control module mounting screws are longer than the others. These longer screws secure the top side of the control module to the rear mounting locations.<\/i><\/p>\n<\/div>\n<\/li>\n<li>\n<p>Gently raise the bottom of the control module to access the front electrical harnesses.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_002.png\" alt= \"control panel screws\"><\/li>\n<li>\n<p>Disconnect the four (4) electrical harnesses.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_003.png\" alt= \"electrical harnessing\"><\/li>\n<li>\n<p>Continue raising the module to access and disconnect the flex cable.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_004.png\" alt= \"electrical harnessing\"><\/li>\n<li>\n<p>Disconnect the seven (7) rear electrical harnesses.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_005.png\" alt= \"electrical harnessing\">\n\t<\/li>\n<li>\n<p>Remove the control module.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_006.png\" alt= \"control panel removed\"><\/li>\n<\/ol>\n<h2>Control Module Installation (Fusion Maker &#038; Edge)<\/h2>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>Attach the anti-static strap.<\/li>\n<li>\n<p>Place the control module in position.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_007.png\" alt= \"control panel positioning\"><\/li>\n<li>\n<p>Connect the seven (7) rear electrical harnesses.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_005.png\" alt= \"electrical harnessing\"><\/li>\n<li>\n<p>Connect the flex cable.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_004.png\" alt= \"electrical harnessing\"><\/li>\n<li>\n<p>Connect the four (4) front electrical harnesses.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_003.png\" alt= \"electrical harnessing\"><\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-primary uk-h4\"><i class=\"fas fa-exclamation-circle uk-margin-small-right\"><\/i>Note: <\/span><\/strong>The X-Axis drive and fiber source receptacle both use a display port connector. Ensure that the display port cable is plugged in to the appropriate receptacle when reconnecting the front electrical harnesses.<\/i><\/p>\n<\/div>\n<\/li>\n<li>\n<p>Install and tighten the four (4) screws (ensure longer screws are in the rear).<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_001.png\" alt= \"control panel screws\"><\/li>\n<li>Reconnect power and turn on the engraver.<\/li>\n<\/ol>\n<h3>Programming the Control Module<\/h3>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>\n<p>At the display panel, press the gear icon in the upper right-hand corner of the display to open the Settings menu:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/gear.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Press Update:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/settings.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Press Program Peripherals<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/update.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Once in the Peripheral Update menu, select all available components and press Update:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/peripheral_update.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Allow the engraver to run the update process.<\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-danger uk-h4\"><i class=\"fas fa-exclamation-triangle uk-margin-small-right fa-2x\"><\/i>Warning: <\/span><\/strong>When running a peripheral update, do not power off the engraver. During a peripheral update, it is common for the display to power off. Once the update has been applied, the engraver will prompt to restart.<\/i><\/p>\n<\/div>\n<\/li>\n<li>Once the engraver prompts you to restart, power cycle the engraver.<\/li>\n<\/ol>\n<h2>Control Module Removal (Pro 24\/36)<\/h2>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>Turn off the engraver.<\/li>\n<li>Disconnect power source.<\/li>\n<li>Open the top door of the engraver.<\/li>\n<li>Disconnect the connection cables.<\/li>\n<li>Remove the right panel.<\/li>\n<li>Attach the anti-static strap.<\/li>\n<li>\n<p>Loosen and remove the four (4) 5\/32\u201d Allen screws.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_001.png\" alt= \"control panel screws\"><\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-primary uk-h4\"><i class=\"fas fa-exclamation-circle uk-margin-small-right\"><\/i>Note: <\/span><\/strong>The control module on the Fusion Pro 24 and Fusion Pro 36 interfaces with the engraver much differently than the Fusion Edge engraver. Whereas the Fusion Edge engraver houses electrical connections directly on the underside of the control module, the Fusion Pro 24 and Fusion Pro 36 engraver control module uses two (2) multi-pin connectors that interface with a backplane board. Take care when removing and installing the control module, ensuring that the multi-pin connectors are not damaged.<\/i><\/p>\n<\/div>\n<\/li>\n<li>\n<p>Gently raise the bottom of the control module to unseat the multi-pin connectors.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_002.png\" alt= \"electrical harnessing\"><\/li>\n<li>Remove the control module.<\/li>\n<\/ol>\n<h2>Control Module Installation (Pro 24\/36)<\/h2>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>Attach the anti-static strap.<\/li>\n<li>\n<p>Position the control module aligning the screw holes.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_008.png\" alt= \"control panel screws\"><\/li>\n<li>\n<p>Apply gentle pressure to seat the multi-pin connectors.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_009.png\" alt= \"control panel installation\"><\/li>\n<li>\n<p>Ensure proper positioning before proceeding.<\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-primary uk-h4\"><i class=\"fas fa-exclamation-circle uk-margin-small-right\"><\/i>Note: <\/span><\/strong>If the control module does not seat with gentle pressure, do not force it down as the multi-pin connectors may become damaged. Lift the control module away from the engraver and ensure proper positioning with the chassis of the engraver before attempting installation again<\/i><\/p>\n<\/div>\n<\/li>\n<li>\n<p>Install and tighten the screws.<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/17k_control_board_001.png\" alt= \"control panel screws\"><\/li>\n<li>Reconnect power and turn on the engraver.<\/li>\n<\/ol>\n<h2>Programming the Control Module<\/h2>\n<ol class=\"uk-list uk-list-decimal uk-list-divider uk-list-large\">\n<li>\n<p>At the display panel, press the gear icon in the upper right-hand corner of the display to open the Settings menu:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/gear.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Press Update:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/settings.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Press Program Peripherals<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/update.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Once in the Peripheral Update menu, select all available components and press Update:<\/p>\n<p>\t\t<img decoding=\"async\" class=\"uk-margin-bottom\" src=\"https:\/\/support.epiloglaser.com\/staging\/assets\/img\/knowledge-base\/display_menus\/peripheral_update.png\" width= \"350\" alt= \"screenshot\"><\/li>\n<li>\n<p>Allow the engraver to run the update process.<\/p>\n<div class=\"uk-panel uk-tile-muted uk-padding\">\n<p><i><strong><span class=\"uk-text-danger uk-h4\"><i class=\"fas fa-exclamation-triangle uk-margin-small-right fa-2x\"><\/i>Warning: <\/span><\/strong>When running a peripheral update, do not power off the engraver. During a peripheral update, it is common for the display to power off. Once the update has been applied, the engraver will prompt to restart.<\/i><\/p>\n<\/div>\n<\/li>\n<li>Once the engraver prompts you to restart, power cycle the engraver.<\/li>\n<\/ol>\n\r\n\t\t\t<div id=\"daexthefu-container\"\r\n\t\t\t\tclass=\"daexthefu-container daexthefu-layout-side-by-side daexthefu-alignment-left\"\r\n\t\t\t\tdata-post-id=\"18831\">\r\n\r\n\t\t\t\t<div class=\"daexthefu-feedback\">\r\n\t\t\t\t\t<div class=\"daexthefu-text\">\r\n\t\t\t\t\t\t<h3 class=\"daexthefu-title\">Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<div class=\"daexthefu-buttons-container\">\r\n\t\t\t\t\t\t<div class=\"daexthefu-buttons\">\r\n\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-yes daexthefu-button daexthefu-button-type-text\" data-value=\"1\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">Yes<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t\t\r\n\t\t\t<div class=\"daexthefu-no daexthefu-button daexthefu-button-type-text\" data-value=\"0\">\r\n\t\t\t\t<div class=\"daexthefu-button-text\">No<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-comment\">\r\n\t\t\t\t\t<div class=\"daexthefu-comment-top-container\">\r\n\t\t\t\t\t\t<label id=\"daexthefu-comment-label\" class=\"daexthefu-comment-label\"><\/label>\r\n\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-container\">\r\n\t\t\t\t\t\t\t\t<div id=\"daexthefu-comment-character-counter-number\"\r\n\t\t\t\t\t\t\t\t\tclass=\"daexthefu-comment-character-counter-number\"><\/div>\r\n\t\t\t\t\t\t\t\t<div class=\"daexthefu-comment-character-counter-text\"><\/div>\r\n\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<textarea id=\"daexthefu-comment-textarea\" class=\"daexthefu-comment-textarea\"\r\n\t\t\t\t\t\t\t\tplaceholder=\"Type your message\"\r\n\t\t\t\t\t\t\t\tmaxlength=\"\r\n\t\t\t\t\t\t\t\t400\t\t\t\t\t\t\t\t\t\"><\/textarea>\r\n\t\t\t\t\t<div class=\"daexthefu-comment-buttons-container\">\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-submit daexthefu-button\">Submit<\/button>\r\n\t\t\t\t\t\t<button class=\"daexthefu-comment-cancel daexthefu-button\">Cancel<\/button>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t<div class=\"daexthefu-successful-submission-text\">Thanks for your feedback!<\/div>\r\n\r\n\t\t\t<\/div>\r\n\r\n\t\t\t","protected":false},"excerpt":{"rendered":"<p>The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver&#8217;s efficiency and longevity. Control Module [&hellip;]<\/p>\n","protected":false},"author":5,"featured_media":18823,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_helpful_status":1,"_helpful_pro_status":1,"footnotes":""},"categories":[561,557],"tags":[],"laser_machine":[65,66,67],"post_folder":[],"class_list":["post-18831","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-control-circuit-boards","category-service-and-repair","laser_machine-fusion-pro","laser_machine-fusion-edge","laser_machine-fusion-maker"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v27.0 (Yoast SEO v27.8) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Control Module Replacement - Fusion Edge, Maker, Pro - Epilog Support Center<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Control Module Replacement - Fusion Edge, Maker, Pro\" \/>\n<meta property=\"og:description\" content=\"The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver&#8217;s efficiency and longevity. Control Module [&hellip;]\" \/>\n<meta property=\"og:url\" content=\"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/\" \/>\n<meta property=\"og:site_name\" content=\"Epilog Support Center\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/epiloglaser\" \/>\n<meta property=\"article:published_time\" content=\"2025-04-04T17:20:42+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2025-04-04T17:46:42+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"350\" \/>\n\t<meta property=\"og:image:height\" content=\"197\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Tyler Brock\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:site\" content=\"@epiloglaser\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Tyler Brock\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-edge\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/\"},\"author\":{\"name\":\"Tyler Brock\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/db690367f94e26f7d0b8f3bb258d4cdd\"},\"headline\":\"Control Module Replacement &#8211; Fusion Edge, Maker, Pro\",\"datePublished\":\"2025-04-04T17:20:42+00:00\",\"dateModified\":\"2025-04-04T17:46:42+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-edge\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/\"},\"wordCount\":685,\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/thumb_epilog-support-center.jpg\",\"articleSection\":[\"Control \\\/ Circuit Boards\",\"Service and Repair\"],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-edge\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/\",\"name\":\"Control Module Replacement - Fusion Edge, Maker, Pro - Epilog Support Center\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/thumb_epilog-support-center.jpg\",\"datePublished\":\"2025-04-04T17:20:42+00:00\",\"dateModified\":\"2025-04-04T17:46:42+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#primaryimage\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/thumb_epilog-support-center.jpg\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/thumb_epilog-support-center.jpg\",\"width\":350,\"height\":197},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/fusion-pro\\\/control-circuit-boards\\\/control-module-replacement-fusion-edge-maker-pro\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Control Module Replacement &#8211; Fusion Edge, Maker, Pro\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#website\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"name\":\"Epilog Support Center\",\"description\":\"Imagine. Design. Create.\",\"publisher\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#organization\",\"name\":\"Epilog Laser\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"contentUrl\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/wp-content\\\/uploads\\\/epilog-logo.png\",\"width\":215,\"height\":46,\"caption\":\"Epilog Laser\"},\"image\":{\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/epiloglaser\",\"https:\\\/\\\/x.com\\\/epiloglaser\",\"https:\\\/\\\/www.instagram.com\\\/epiloglaser\\\/\",\"https:\\\/\\\/www.youtube.com\\\/@epiloglaser\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/epilog\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/#\\\/schema\\\/person\\\/db690367f94e26f7d0b8f3bb258d4cdd\",\"name\":\"Tyler Brock\",\"url\":\"https:\\\/\\\/support.epiloglaser.com\\\/staging\\\/laser-machine\\\/author\\\/tyler\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Control Module Replacement - Fusion Edge, Maker, Pro - Epilog Support Center","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/","og_locale":"en_US","og_type":"article","og_title":"Control Module Replacement - Fusion Edge, Maker, Pro","og_description":"The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver&#8217;s efficiency and longevity. Control Module [&hellip;]","og_url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/","og_site_name":"Epilog Support Center","article_publisher":"https:\/\/www.facebook.com\/epiloglaser","article_published_time":"2025-04-04T17:20:42+00:00","article_modified_time":"2025-04-04T17:46:42+00:00","og_image":[{"width":350,"height":197,"url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg","type":"image\/jpeg"}],"author":"Tyler Brock","twitter_card":"summary_large_image","twitter_creator":"@epiloglaser","twitter_site":"@epiloglaser","twitter_misc":{"Written by":"Tyler Brock","Est. reading time":"9 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#article","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-edge\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/"},"author":{"name":"Tyler Brock","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/db690367f94e26f7d0b8f3bb258d4cdd"},"headline":"Control Module Replacement &#8211; Fusion Edge, Maker, Pro","datePublished":"2025-04-04T17:20:42+00:00","dateModified":"2025-04-04T17:46:42+00:00","mainEntityOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-edge\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/"},"wordCount":685,"publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg","articleSection":["Control \/ Circuit Boards","Service and Repair"],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-edge\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/","url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/","name":"Control Module Replacement - Fusion Edge, Maker, Pro - Epilog Support Center","isPartOf":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#website"},"primaryImageOfPage":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#primaryimage"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#primaryimage"},"thumbnailUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg","datePublished":"2025-04-04T17:20:42+00:00","dateModified":"2025-04-04T17:46:42+00:00","breadcrumb":{"@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#primaryimage","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/thumb_epilog-support-center.jpg","width":350,"height":197},{"@type":"BreadcrumbList","@id":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/fusion-pro\/control-circuit-boards\/control-module-replacement-fusion-edge-maker-pro\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/support.epiloglaser.com\/staging\/"},{"@type":"ListItem","position":2,"name":"Control Module Replacement &#8211; Fusion Edge, Maker, Pro"}]},{"@type":"WebSite","@id":"https:\/\/support.epiloglaser.com\/staging\/#website","url":"https:\/\/support.epiloglaser.com\/staging\/","name":"Epilog Support Center","description":"Imagine. Design. Create.","publisher":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/support.epiloglaser.com\/staging\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/support.epiloglaser.com\/staging\/#organization","name":"Epilog Laser","url":"https:\/\/support.epiloglaser.com\/staging\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/","url":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","contentUrl":"https:\/\/support.epiloglaser.com\/staging\/wp-content\/uploads\/epilog-logo.png","width":215,"height":46,"caption":"Epilog Laser"},"image":{"@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/epiloglaser","https:\/\/x.com\/epiloglaser","https:\/\/www.instagram.com\/epiloglaser\/","https:\/\/www.youtube.com\/@epiloglaser","https:\/\/www.linkedin.com\/company\/epilog"]},{"@type":"Person","@id":"https:\/\/support.epiloglaser.com\/staging\/#\/schema\/person\/db690367f94e26f7d0b8f3bb258d4cdd","name":"Tyler Brock","url":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/author\/tyler\/"}]}},"_links":{"self":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18831","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/users\/5"}],"replies":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/comments?post=18831"}],"version-history":[{"count":2,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18831\/revisions"}],"predecessor-version":[{"id":18842,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/posts\/18831\/revisions\/18842"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media\/18823"}],"wp:attachment":[{"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/media?parent=18831"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/categories?post=18831"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/tags?post=18831"},{"taxonomy":"laser_machine","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/laser_machine?post=18831"},{"taxonomy":"post_folder","embeddable":true,"href":"https:\/\/support.epiloglaser.com\/staging\/wp-json\/wp\/v2\/post_folder?post=18831"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}