{"id":19509,"date":"2025-05-21T15:35:43","date_gmt":"2025-05-21T21:35:43","guid":{"rendered":"https:\/\/support.epiloglaser.com\/staging\/?p=19509"},"modified":"2025-10-14T13:34:14","modified_gmt":"2025-10-14T19:34:14","slug":"laser-tube-install-zing-24","status":"publish","type":"post","link":"https:\/\/support.epiloglaser.com\/staging\/laser-machine\/zing\/laser-source\/laser-tube-install-zing-24\/","title":{"rendered":"Full Guide: Replacing the Laser Assembly"},"content":{"rendered":"
\n

Laser Removal:<\/h2>\n
    \n
  1. Lower the table to the bottom of the machine.<\/li>\n
  2. Turn off the machine.<\/li>\n
  3. Disconnect the machine from its power source.<\/li>\n
  4. \n

    Remove the four Phillips screws which secure the left-hand side panel. There are three on the side and one on the rear as shown in picture 1a and 1b.<\/p>\n

    \"\"<\/p>\n

    \"\"<\/p>\n<\/li>\n

  5. \n

    Remove the side panel.<\/p>\n<\/li>\n

  6. \n

    Disconnect the laser power connection, shown in picture 2, from the machine\u2019s chassis. The connection is located above and behind the laser assembly. There is a lock on the connection\u2014depress the lock and pull the connection toward you.<\/p>\n

    \"disconnect<\/p>\n<\/li>\n

  7. \n

    Disconnect the data cable from the laser assembly. The data cable is shown in picture 3. This connection works the same as your network cable. There is a lock on the connection that must be depressed before the connector will come out of the laser tube.<\/p>\n

    \"disconnect<\/p>\n<\/li>\n

  8. \n

    The laser is held in place by three green mounting screws. The mounting screws are located on the laser tube itself. The location of the mounting screws is shown in picture 4.<\/p>\n

    \"green<\/p>\n<\/li>\n

  9. \n

    The 3 mounting screws are captive screws. You will only need to loosen them to remove the laser tube.<\/p>\n

    \"green<\/p>\n<\/li>\n

  10. \n

    Once the laser mounting screws are loosened, you will note that the Laser guide pin fits into a slot in your engraver\u2019s chassis. To remove the laser assembly, lift it slightly and move the laser assembly so that the Laser Guide pin head is lined up with the hole in the machine\u2019s chassis. The laser can now be removed from the machine.<\/p>\n<\/li>\n<\/ol>\n

    Laser Installation:<\/h2>\n
      \n
    1. \n

      Align the laser\u2019s guide pins with the holes in the side of the machine\u2019s chassis and push the laser assembly against the side of the machine. Then slide the laser assembly toward the front of the machine.<\/p>\n<\/li>\n

    2. \n

      Loosely install the three screws in each of the laser mounting plates. Once all three screws have been loosely installed, tighten all of the mounting screws.<\/p>\n<\/li>\n

    3. \n

      Reconnect the data cable to the laser assembly, as shown in picture 6.<\/p>\n

      \"connect<\/p>\n<\/li>\n

    4. \n

      Reconnect the laser\u2019s power harness to the chassis as shown in picture 7.<\/p>\n

      \"connect<\/p>\n<\/li>\n

    5. \n

      Follow the Zing Laser Alignment<\/a> instructions after completing the installation procedure.<\/p>\n<\/li>\n<\/ol>\n\r\n\t\t\t

      \r\n\r\n\t\t\t\t
      \r\n\t\t\t\t\t
      \r\n\t\t\t\t\t\t

      Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t
      \r\n\t\t\t\t\t\t
      \r\n\t\t\t\t\t\t\t\r\n\t\t\t
      \r\n\t\t\t\t
      Yes<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t\t\r\n\t\t\t
      \r\n\t\t\t\t
      No<\/div>\r\n\t\t\t<\/div>\r\n\r\n\t\t\t\t\t\t\t\t\t<\/div>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t<\/div>\r\n\r\n\t\t\t\t
      \r\n\t\t\t\t\t
      \r\n\t\t\t\t\t\t