Archives des services et réparations

Remplacement du moteur en Y

Remplacez le moteur qui fait avancer et reculer l'ensemble de l'axe X de votre machine.

Remove Right Panel Remove the right side panel by removing the 6 screws, 4 located on the side of the machine, two located on the back of the machine. Remove Old Y-Motor Open the front access door. Locate the Y-Motor on the right hand-side of the machine. Remove the spring (...)

09/24/2024

Remplacement du moteur X

Remplacez le moteur qui déplace la tête laser de votre machine le long de l'ensemble de l'axe X.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

04/11/2025

Puissance élevée

Résoudre un problème d'alimentation : remplacement de la double alimentation électrique

Comment remplacer le Helix bloc d'alimentation Mini / Helix .

Remove Back Panel Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the two power supplies. Disconnect Electrical Leads Disconnect four of the electrical leads. Disconnect the two connectors holding (...)

10/14/2025

Faible puissance

Résoudre un problème d'alimentation : remplacement du bloc d'alimentation

Comment remplacer l'alimentation électrique Helix du Mini / Helix .

Remove Old Power Supply Shut off the laser and remove the power cord from the machine. Loosen the 8 screws on the back of the machine and remove the back service panel. Locate the power supply on the left hand side of the machine. Disconnect the three electrical leads. With (...)

10/14/2025

Remplacement de l'écran / du clavier

Remplacez le panneau d'affichage/clavier de votre machine.

Remove Side Panels Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove (...)

04/14/2025

Réglages CO2 Tickle

Que sont les paramètres de chatouillement et comment puis-je les régler ?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

04/02/2025

Remplacement optique –Helix

Comment remplacer la lentille de mon Helix de mon Mini ?

This guide provides step-by-step instructions for replacing the carriage, steering, and periscope optics in your laser system. Follow the outlined procedures carefully to ensure proper installation and alignment. Always handle optics with care and refer to the provided alignment links after replacement to maintain optimal performance. Replacing Carriage Optics Move (...)

04/03/2025

Guide détaillé pour le démarrage à froid

Mon laser est inactif depuis longtemps et ne fonctionne plus.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

04/08/2025

Vérification et mise à niveau de la table

Si vous remarquez une gravure inégale ou une puissance réduite dans certains coins de votre Mini ou Helix, il se peut que la table ne soit pas à niveau. Ce guide explique comment vérifier et mettre à niveau la table pour obtenir des performances optimales.

Estimated time: 15-20 minutes • Skill: Beginner A perfectly level engraving table is essential for accurate focusing and consistent engraving results. This guide will walk you through checking and adjusting the table level on your Epilog Mini or Helix laser system. Checking Table Level Access the table. Power on the (...)

10/23/2025