Service- en reparatiearchief

Hoe vervang je de kabels van de camera boven je hoofd?

Leer hoe je de kabels van de camera boven je hoofd vervangt op de Epilog Fusion Edge, Maker- en Pro 24/36-lasersystemen met deze stap-voor-stap videogids.

Lees meer

09/23/2025

Hoe installeer je de trekontlastingsset?

Hoe zet ik de trekontlastingsset op mijn epilog laser?

Estimated time: 10–15 minutes • Skill: Basic This guide explains how to install the strain relief kit on the lens carriage of your Epilog Laser system. The kit includes a harness clamp and mounting hardware designed to guide and secure the autofocus and camera cables as they move with the (...)

Lees meer

09/19/2025

LC1000 – Overzicht van poorten en LED's van de bedieningsmodule

The control module on Epilog laser systems provides connection points and LED indicators that offer system status and control feedback. This guide outlines each port and indicator located on the right side of the machine. Port Descriptions Exhaust Control: Connects to a compatible exhaust unit to send on/off commands. USB (...)

Lees meer

03/24/2026

De lineaire geleiding schoonmaken en smeren (IKO)

This guide provides detailed instructions for cleaning and greasing the linear guide rail on your Epilog Laser system. Over time, debris and buildup can affect motion smoothness and engraving accuracy. Performing regular maintenance helps ensure optimal performance and extends the life of your equipment. Follow each step carefully, and refer (...)

Lees meer

12/30/2025

SD-kaarten flashen

Leer hoe je een SD-kaart kunt flashen voor Epilog Laser met Balena Etcher.

This guide outlines the steps for flashing an SD card for your laser system. A technician must provide the required disc image file to complete this process. Do not proceed without first obtaining the correct file specific to your machine. Flashing SD Cards SD Card Removal Remove the control board (...)

Lees meer

06/19/2025

Wizard voor het kalibreren van de autofocus

Estimated Time: 2–5 Minutes | Skill Level: Basic The Autofocus Calibration Wizard allows the laser system to automatically determine the correct autofocus height using a calibrated reference surface. This process ensures accurate and consistent autofocus performance across supported materials. Running the Autofocus Calibration Wizard Open the Settings Menu (...)

Lees meer

03/24/2026

Wizard voor het kalibreren van de focus

Stapsgewijze handleiding voor het gebruik van de Focus Calibration Wizard, beschikbaar in firmwareversie 1.1.2.1 en hoger.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

Lees meer

03/16/2026

Pro 24, Pro 36

Vervanging van lineaire geleiding (IKO) – Large Aperture Fusion Pro

Removal Procedure Power OFF the machine and disconnect the power cord. Remove the right and left side panels. Open the top door. Pull the rail to the middle of the machine. Move the carriage to the center. Loosen the thumb screws and open the mirror cover. Disconnect the air assist (...)

Lees meer

05/20/2025

Pro 24, Pro 36

Autofocus-schakelaar vervangen – Fusion Maker, Edge, Pro 24 & 36

Hoe vervang ik de autofocusknop in de Fusion Maker, Edge en Pro 24 en 36?

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

Lees meer

05/07/2025

Service en reparatie

Filters

Filters

Preventief onderhoud van lasersystemen

LC1000-TS Diagnostische wizard

De X-asriem afstellen

Hoe vervang je de kabels van de camera boven je hoofd?

Hoe installeer je de trekontlastingsset?

LC1000 – Overzicht van poorten en LED's van de bedieningsmodule

De lineaire geleiding schoonmaken en smeren (IKO)

SD-kaarten flashen

Wizard voor het kalibreren van de autofocus

Wizard voor het kalibreren van de focus

Vervanging van lineaire geleiding (IKO) – Large Aperture Fusion Pro

Autofocus-schakelaar vervangen – Fusion Maker, Edge, Pro 24 & 36