Service- en reparatiearchief

Optiek schoonmaken – Fusion Maker, Edge en Pro

In dit document wordt uitgelegd hoe je de optische onderdelen van de Fusion Maker, Edge en Pro op de juiste manier schoonmaakt.

Daily Maintenance Cleaning Remove the lens and carriage mirror. Safely detach both the lens and carriage mirror using the video guide below. Figure 1. Lens and carriage mirror removal process. Carriage Optics Removal Steps Disconnect the air tubing from the lens. Loosen the thumb screws on the carriage cover and (...)

Lees meer

12/31/2025

Mijn kunstwerk wordt niet weergegeven in het Epilog-dashboard.

Mijn kunstwerk wordt niet weergegeven in het Epilog-dashboard en de looptijd geeft 0:00 aan?

Explanation of the Symptoms When encountering this issue, you may see something similar to the image below—here we can see the artwork in the preview thumbnail, but the artwork does not appear in the work area: However, if zoomed out, we can see that the artwork did transfer to the (...)

Lees meer

04/25/2025

Pro 24, Pro 36

Handmatige kalibratie van de focusmeter – Fusion Maker, Edge, Pro

Leer hoe je de handmatige focusmeter op een Fusion Maker-, Edge- of Pro-machine kunt kalibreren.

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

Lees meer

12/31/2025

Pro 24, Pro 36

Hoe vervang je de motorbesturing van de X-as: stap voor stap uitgelegd

Leer hoe je de TE0104 X-as-aandrijfkaart vervangt op 17000 Edge- en Pro-machines. Deze reparatie kan verschillende bewegingsproblemen met de X-as oplossen en helpen om de machine weer soepel te laten werken.

This guide will walk you through the process of removing, installing, and programming the X-Axis Drive Board for Fusion Edge and Pro 24 / 36 models. Proper precautions, including the use of an anti-static strap, are essential to ensure the safe handling of electronic components. Drive Board Replacement Procedure Models: (...)

Lees meer

11/11/2025

Machinelogboeken maken

Hoe maak ik de machinelogboeken aan?

Generating machine logs enables Epilog Technical Support to gather important information about the machine, aiding in its diagnosis and troubleshooting. The process is straightforward and requires either a USB flash drive or a network-connected machine. This guide will outline the steps for generating logs. Logs can be generated one of (...)

Lees meer

04/11/2025

Schoonmaakprocedures – Fusion Maker, Edge en Pro

Dit document legt uit hoe je de Fusion Maker, Edge en Pro-machine schoonmaakt en onderhoudt.

Regular cleaning of the Fusion Pro engraver will result in a longer service life of the engraver and less down time. Additionally, regular cleaning of the Fusion Pro engraver can mitigate the risk of flare-ups and other thermal events. A mild household cleaner or degreaser can be used to clean (...)

Lees meer

12/31/2025

Checklist voor het vervangen van CO2 / Lage output

Deze handleiding helpt je bij het opsporen en oplossen van problemen met een lage output van je lasersysteem uit de 17000-serie.

Having to continually reduce speed and increase power can indicate low output from the laser. This document will help identify a low output laser tube on a 17000 Maker, Edge, or Pro machine. Checklist Optics Alignment Focus Reference Engraving Download the sample file below. Reference Engraving Open the file and (...)

Lees meer

04/09/2025

Pro 24, Pro 36

Vervanging van de bedieningsmodule – Fusion Edge, Maker, Pro

The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver’s (...)

Lees meer

04/04/2025

Randstandaardmontage

Hoe zet ik mijn Edge Laser-standaard in elkaar?

The Fusion Edge Stand is an essential accessory designed to support your laser system with stability and ease of mobility. Whether you’re setting up a new machine or replacing an existing stand, this guide provides step-by-step instructions to help you assemble the stand safely and efficiently. By carefully following each (...)

Lees meer

04/04/2025

Checklist voor het vervangen van CO2 / Geen output

Deze handleiding helpt je bij het opsporen en oplossen van problemen met je 17000-serie lasersysteem waarbij er geen uitvoer is.

These items should be checked before replacing a CO2 laser tube with no output. If the laser has been inactive for more than one (1) month, follow the Extended Cold Start Guide first. The goal of this document is to determine the operational status of the CO2 laser in a (...)

Lees meer

04/09/2025

Snelle handleiding: De joystick kalibreren voor nauwkeurige bewegingen

Door de joystick te kalibreren, kun je problemen oplossen zoals vertraagde bewegingen, onnauwkeurige besturing of het zelfstandig verschuiven van de slede in de jogmodus.

Steps to Calibrate the Joystick Open the Settings Menu On the display panel, press the gear icon in the top-right corner to open the Settings menu. Image 1: Home screen with gear icon in top-right corner Access Advanced Settings Press and hold the word “Settings” on the screen until the (...)

Lees meer

03/16/2026