Didn’t find what you were looking for?

Search Results for "8000 - Fibermark"

• Maximum Rotary Attachment Diameters

  Maximum diameter that will fit on the Rotary Attachment for each system Epilog Zing 24: 5.25" (133mm) Epilog Mini 18: 3" (76mm) Epilog Mini 24: 5" (127mm) Epilog Helix: 8" (203mm) Fusion 32: 10.75" (273 mm) Fusion 40: 10.75" (273 mm) Fusion M2 32: 10.25" (260 mm) Fusion M2 40: 10.25" (260 mm) Fusion Pro 32: 9.25" (234 mm) Fusion Pro 48: 9.25" (234 mm) Fusion Edge 12: 4" (101 mm) Fusion Edge 24: 7" (177 mm) FiberMark Rotary Attachment Diameter Capabilities Standard Rotary 1.5" Lens: 4.25" (109 mm) 3" Lens: 2.75" (70 mm) 5" Lens: 1.0" (26 mm) 3- Jaw / Clamp Rotary 1.5" Lens: 3.25" (83 mm) 3" Lens: 1.75" (44 mm) 5" Lens: n/a The maximum length of object that can be used in the 3-Jaw Chuck Rotary Attachment is as follows: 3-jaw chuck: 470mm All other fixtures: 500mm Total length of 3-jaw chuck rotary: 66cm

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: Rotary | 3-Jaw | Diameter

• How to Laser Engrave and Cut Fabrics

  Natural fibers, as well as synthetic fabrics, are often cut and engraved with fantastic results with a laser system.

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: Applique | Twill | Cotton | Leather | Material Compatibility | Engraving Tips

• Setting up a Gun Stock for Engraving

  Figure 3a Figure 3b 4) Viewing the gun stock on its side, place a dot 6.5" from the bottom mark, then measure .75" up from the bottom of the stock and place a dot (pictured right).

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: Gun Stock | Design Tips | Artwork Setup

• Duplicating Around a Center Point in CorelDRAW

  Drag in the guidelines from the rulers at the top of the page and the side of the page to mark the center point of the hexagon. 2) Next, create one of the arms to the snowflake.

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: CorelDRAW | Artwork | Design Tips | Center Point

• 17000 - CO2 Laser Replacement Checklist / Low Output

  Get a burn mark by tapping the Activate button and watching for a burn mark on the tape.

  Machine Series: Fusion Maker, Fusion Edge, Fusion Pro

  Keywords: Checklist | Laser | Low Power | Laser Replacement

• How to set up a project on the Vector Pin Table

  This allows the laser to cut through the material, without the backside burning or leaving grid marks. 1) To start, we've set our page size to the size of the Vector Pin Table, 12" x 12".

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: Pin Table | Project | Usage | Vector

• 16000 - Fusion Pro 32 & 48 - Power Supply Replacement

  Required Tools and Parts 5/32" Hex Wrench CS0830 - Assy, Power Supply, 2kW CS0953 - Assy, Power Supply, 24V, 1kW (Dual and Fiber Souce Engravers Alignment Target Phillips Head Screwdriver Power Supply Locations CO2- Only Fusion Pro This model will contain only the CO2 power supply shown above.

  Machine Series: Fusion Maker, Fusion Edge, Fusion Pro

  Keywords: Fusion Pro | Power Supply | PSU | Install

• Loss of Power in a Epilog Mini/Helix

  First, check the optics for any damage, including burn marks, pock marks, scratches, cracks, flaking of the layers on the mirror or discoloration of any kind.

  Machine Series: Mini, Helix, Fibermark

  Keywords: Mini | Helix | Low Power | Dirty Optics | Not Cutting

• Wireless Printing to an Epilog Laser Using a Router

  Did you know that current Epilog laser systems (Zing, Mini, Helix, EXT and FiberMark) have the ability to be set up as a wireless printer?

  Machine Series: Mini, Helix, Fibermark | Legend 36EXT | Zing | Fusion, Fusion M2 | Fusion Maker, Fusion Edge, Fusion Pro | Fusion Galvo | Legacy Systems

  Keywords: Wireless | Router | Networking

• 16000 - Fusion Pro 32 & 48 - Leveling the Table

  If all areas of the table are not the same distance from the focusing lens, loss of laser power and inconsistent engraving and cutting marks can occur.Complete this procedure if any of the following behaviors are observed: Laser power appears weak in certain areas of the table.

  Machine Series: Fusion Maker, Fusion Edge, Fusion Pro

  Keywords: Fusion Pro | Table Level | Low Power | Service Procedures