Archives d'utilisation et de fonctionnement

Placer du texte sur un tracé dans CorelDRAW

Comment placer du texte sur un tracé dans CorelDRAW?

Have you ever had that engraving job that would have looked even better if you could have just curved the text around the photograph, or been able to have the text along a line you drew? Well, it’s possible in a few easy steps in CorelDRAW! Follow the directions below (...)

03/31/2025

PhotoLaser Plus Démarrage rapide

Comment utiliser PhotoLaser Plus avec mon laser ?

This page is to provide you with special settings that we’ve developed with CADLink for PhotoLaser Plus, as well as to provide you with some quick tips that we think you’ll find helpful when using the software. Download and unzip the attached material profile settings into your C:PhotoLaser Plus (...)

04/01/2025

Exigences en matière d'alimentation électrique en fonction de la puissance du laser

Quelles sont les exigences en matière d'alimentation électrique pour mon Epilog en fonction de la puissance du laser ?

Systems: All This information is to be used only to size a power condition or an UPS (uninterruptible power supply)and should not be used to size the circuit providing voltage to the system. The circuit requirement remains as a 15 amp circuit. Laser Type Wattage Voltage Requirements Wattage of Power (...)

04/01/2025

Optimisez votre flux de travail : modification des paramètres par défaut des tâches

Comment puis-je configurer les paramètres par défaut dans la suite logicielle ?

Estimated time: 5–10 minutes • Skill: Beginner By default, jobs sent to the Epilog Software Suite use standard settings. You can customize these defaults to save setup time or better match your materials and applications. Follow the steps below to change the default job settings. Changing Default Job Settings Send (...)

10/16/2025

Sécurité des matériaux et votre laser

Qu'est-ce qu'une fiche de données de sécurité et comment l'utiliser ?

While nearly any material you put into your engraving system will contain and or release some sort of residue or debris, generally speaking, most materials are safe to use in your system. However, there are certain materials not suited for laser engraving and cutting – these materials can corrode the (...)

05/02/2025

Consommation électrique et votre laser

Quelle est la consommation électrique d'un Epilog Laser et quel est son coût de fonctionnement final ?

Using the formula and information below, you can discover how much power our laser systems draw as well as how much it costs to operate a laser. Most users are pleasantly surprised at how energy and cost efficient these powerful systems are – even our highest-wattage machine costs less than (...)

04/01/2025

Choisir une alimentation sans coupure pour votre Epilog Laser

Quelle alimentation sans coupure convient le mieux à mon Epilog Laser ?

Spring is a time for many things, including unpredictable weather. While many people have battery backup for clocks, computers and other important devices, many don’t think of taking this important precaution when it comes to their laser. No one wants to lose a whole project because of an unexpected power (...)

04/01/2025

Comment choisir la puissance de mon système laser ?

Comment choisir la puissance laser adaptée à mes besoins ?

The power of the laser source is measured in watts. Depending on the machine you are considering you will have power options for your laser source that range from 30-120 watts for CO2 laser tubes. Generally speaking, lower power CO2 laser tubes will be able to process the same materials, (...)

04/01/2025

Suggestions pour la gravure de codes-barres

Comment graver un code-barres très petit au laser ?

There are a lot of variables which determines whether your 2D barcode engraving will be successful. The contrast you can achieve on the PCB, the amount of data contained within the 2D barcode, size of barcode and most importantly, the scanner you’re using. When you’re trying to engrave a very (...)

04/01/2025

Quelle quantité de gaz combustible est libérée lors de la gravure au laser ?

La gravure au laser libère-t-elle des gaz combustibles dangereux ?

Combustible gas release from laser engraving is extremely minuscule. When materials are engraved with a laser, they emit combustion products. These consist largely of simple carbon smoke and debris. Gases are also produced; typical combustion gas products for some common engraving materials are shown below. The values are provided in (...)

04/01/2025

Laser YAG vs. CO2

Quelle est la différence entre un CO2 YAG et CO2 ?

Two of the most common types of lasers you hear about are YAG and CO2. While Epilog manufactures a CO2 laser system, we wanted to give you some information about the two different types of laser systems and which one may be right for your application. Both CO2 lasers and (...)

04/01/2025

Exigences relatives aux échappements laser

Quelles spécifications dois-je prendre en compte lors du choix d'un système d'échappement ?

Systems: All When specifying an exhaust system for your machine there are a number of considerations. The main minimum requirements that must be followed: CFM (Cubic Feet per Minute) or M3/hr (metric): This is the amount of air that a blower or exhaust system can move per hour of operation. The (...)

04/01/2025

Utilisation et fonctionnement

Filtres

Filtres

Placer du texte sur un tracé dans CorelDRAW

PhotoLaser Plus Démarrage rapide

Exigences en matière d'alimentation électrique en fonction de la puissance du laser

Optimisez votre flux de travail : modification des paramètres par défaut des tâches

Sécurité des matériaux et votre laser

Consommation électrique et votre laser

Choisir une alimentation sans coupure pour votre Epilog Laser

Comment choisir la puissance de mon système laser ?

Suggestions pour la gravure de codes-barres

Quelle quantité de gaz combustible est libérée lors de la gravure au laser ?

Laser YAG vs. CO2

Exigences relatives aux échappements laser