Service and Repair Archives

Autofocus Calibration Wizard

Estimated Time: 2–5 Minutes | Skill Level: Basic The Autofocus Calibration Wizard allows the laser system to automatically determine the correct autofocus height using a calibrated reference surface. This process ensures accurate and consistent autofocus performance across supported materials. Running the Autofocus Calibration Wizard Open the Settings Menu (...)

03/24/2026

Focus Calibration Wizard

Step-by-step guide to using the Focus Calibration Wizard, available in firmware version 1.1.2.1 and later.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/16/2026

Pro 24, Pro 36

Manual Focus Gauge Calibration – Fusion Maker, Edge, Pro

Learn how to calibrate the manual focus gauge on a Fusion Maker, Edge, or Pro machine.

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

12/31/2025

Table Leveling Procedure – Legend 36EXT

How do I level the table on my Legend 36EXT?

Maintaining a level engraving table is essential for achieving precise and consistent results with your Epilog Legend 36EXT. This procedure provides detailed instructions for checking the level of the table using the manual focus gauge and outlines steps to correct any imbalance. Proper table leveling ensures accurate laser focus across (...)

12/31/2025

Setting Home Position – Legend 36EXT

This document explains how to set the home position on the Legend 36EXT

This procedure will guide you through the steps necessary to set the X-Y home on the Epilog 36EXT laser engraver. Accurate setting of the X and Y axes is essential for precise engraving and cutting, ensuring that your artwork aligns properly with the material. Follow each step carefully to ensure (...)

12/31/2025

Perpendicular Alignment – Legend 36EXT

How do I correct the perpendicular alignment on the Legend 36EXT

This procedure details how to correct the alignment on the Epilog EXT laser system to ensure the Red Dot pointer, and ultimately the laser beam, is perpendicular to the engraving table. Accurate perpendicular alignment is critical for producing clean, precise vector cuts. Before starting, it’s essential to complete the EXT (...)

12/31/2025

Pro 24, Pro 36

Laser Alignment (Large Aperture Optics) – Fusion Pro

How do I align the laser on my Fusion Pro with large aperture optics.

To ensure your CO2 laser engraver delivers optimal performance and consistent cutting quality, proper beam alignment is essential. Over time, vibration, wear, or component replacement can cause the laser beam to deviate from its intended path. This can result in reduced cutting power, inconsistent engraving, or premature wear of optics. (...)

12/31/2025

X-Y Home Position Calibration

How do I set the X/Y home position on my Epilog Mini or Helix?

This article is a step-by-step guide on how to do the X-Y Home Position Calibration on the Epilog Mini 18/24 and Helix. Machine Type: Epilog Mini 18/24, Helix Tools Needed: Ruler or Measuring Calipers Turn on the engraver. Open a new page in Corel Draw. Create a 1 inch black (...)

12/31/2025

Pro 32, Pro 48

CO2 Laser Alignment – Fusion Pro 32 & 48

How do I align the CO2 laser in the Fusion Pro 32 and 48?

Please find the attachment for an in-depth description.

12/31/2025

Laser Alignment – Legend 36EXT

How do I align the laser in my 36EXT?

Please find the attachment for an in-depth description.

12/31/2025

Pro 24, Pro 36

Focus Calibrations – Fusion Maker, Edge, and Pro

How do I calibrate the focus in the Fusion Maker, Fusion Edge, and Fusion Pro?

Please find the attachment for an in-depth description.

12/31/2025

Pro 32, Pro 48

Fiber Alignment – Fusion Pro 32 & 48

How do I align the laser in my Fusion Pro Fiber or Dual source machine.

This guide provides step-by-step instructions for performing precise laser alignment on the Fusion Pro CO2 and Fiber laser systems. Proper alignment ensures optimal engraving performance and reduces the risk of hardware damage. Whether you’re troubleshooting a drop in laser power or aligning after maintenance, this document will walk you through (...)

12/31/2025

Calibrations

Filters

Filters

Autofocus Calibration Wizard

Focus Calibration Wizard

Manual Focus Gauge Calibration – Fusion Maker, Edge, Pro

Table Leveling Procedure – Legend 36EXT

Setting Home Position – Legend 36EXT

Perpendicular Alignment – Legend 36EXT

Laser Alignment (Large Aperture Optics) – Fusion Pro

X-Y Home Position Calibration

CO2 Laser Alignment – Fusion Pro 32 & 48

Laser Alignment – Legend 36EXT

Focus Calibrations – Fusion Maker, Edge, and Pro

Fiber Alignment – Fusion Pro 32 & 48