Page 11 – Epilog Support Center

CO2 Laser Replacement Checklist / No Output

This guide will assist you in diagnosing and resolving no output issues with your 17000 series laser system.

These items should be checked before replacing a CO2 laser tube with no output. If the laser has been inactive for more than one (1) month, follow the Extended Cold Start Guide first. The goal of this document is to determine the operational status of the CO2 laser in a (...)

04/09/2025

X-Axis Flex Cable Install – 36EXT

How do I install the X-Axis flex cable on my 36EXT?

The X-axis flex cable plays a crucial role in the operation of the Epilog Legend 36EXT engraver. Over time, the cable may wear out or become damaged, requiring replacement. This guide provides step-by-step instructions to safely replace the X-axis flex cable, ensuring that your engraver continues to perform at its (...)

04/08/2025

Y-Axis Flex Cable Install – Mini / Helix

How do I install the y-axis flex cable into my Mini, Helix, or Fibermark machine?

This document provides detailed instructions for the removal and installation of the Y-Axis Flex Cable in the Epilog Mini/Helix and FiberMark Laser Engravers. Proper alignment and handling of the cable are essential to maintaining the machine’s performance and functionality. By following these steps carefully, users can ensure a smooth replacement (...)

04/10/2025

Squaring the Ruler Guides

How do I realign the ruler guides on my Mini or Helix?

Machine Types: Epilog Mini 18/24, Helix If your rulers have been moved accidentally or on purpose and you would like to return them to their original positioning, and by following these simple steps it will walk you through the process. Turn Power off. Place a 2 inch strip of masking (...)

09/27/2024

Edge Stand Assembly

How do I build my Edge Laser stand?

The Fusion Edge Stand is an essential accessory designed to support your laser system with stability and ease of mobility. Whether you’re setting up a new machine or replacing an existing stand, this guide provides step-by-step instructions to help you assemble the stand safely and efficiently. By carefully following each (...)

04/04/2025

Restore Accuracy: Replacing the X-Axis Encoder Strip

How do I replace the X-Axis encoder strip for my Epilog Mini, Helix, or FiberMark?

Estimated time: 20–30 minutes • Skill: Basic This guide explains how to replace the encoder strip and reader assembly on the Epilog Mini, Helix, or FiberMark laser system. The encoder strip is the thin clear plastic strip that the encoder reader reads to determine X-Axis position; replacing it restores reliable (...)

10/15/2025

Y-Axis Belt Install – Mini / Helix / FiberMark

How do I replace my Y-Belt on my Mini, Helix or FiberMark?

This procedure details steps to replacing the Y-belts. The Y-belt controls the movement of the I-beam from the front and back of the machine. Before starting on this procedure, disconnect the power cord from the machine. Remove both side panels. Loosen the green captive screws on the right side of (...)

04/09/2025

X-Axis Linear Guide Install

How do I replace the linear bearing in my Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit This procedure details steps to replacing the X-axis bearing set. The bearing set is the race and bearing bracket that guides the X-Axis carriage assembly from left to (...)

09/27/2024

X-Axis Rail Install

How do I replace the x-axis rail on my Epilog Mini?

Machine Type: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver Small Philips head screw driver Flat head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit Intro: This procedure details steps to replacing the X-Axis rail on the Legend Mini. The X-Axis rail guides the (...)

04/08/2025

Z-Axis Belt Install

How do I replace the Z-Belt in my Mini?

This procedure details steps to replacing the Z-belt. The Z-belt controls the vertical movement of the engraving table. Before starting on this procedure, raise the engraving table to the top position and disconnect the power cord from the machine. Procedure: Remove both side panels. Remove the front service panel. Remove (...)

04/07/2025

X-Axis Flex Cable Install – Mini / Helix

How do I replace the flex cable on my Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam. Picture 1 Remove I-Beam cover by loosening the two screws on the front side of the beam and the four screws on the rear if you (...)

04/08/2025

X-Axis Belt Replacement – Mini / Helix

How do I replace the x-axis belt on my Mini?

Estimated time: 15–20 minutes • Skill: Basic This guide walks you step-by-step through replacing the X-Axis belt on an Epilog Mini or Helix laser engraver. Follow each instruction carefully to ensure proper installation and avoid damaging your machine. Always power off and unplug the engraver before beginning. To complete this (...)

10/03/2025

Knowledge Base

Filters

Filters

CO2 Laser Replacement Checklist / No Output

X-Axis Flex Cable Install – 36EXT

Y-Axis Flex Cable Install – Mini / Helix

Squaring the Ruler Guides

Edge Stand Assembly

Restore Accuracy: Replacing the X-Axis Encoder Strip

Y-Axis Belt Install – Mini / Helix / FiberMark

X-Axis Linear Guide Install

X-Axis Rail Install

Z-Axis Belt Install

X-Axis Flex Cable Install – Mini / Helix

X-Axis Belt Replacement – Mini / Helix