Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Laser Source

Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (127)

All Usage and Operation System Requirements & Setup (31) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (273)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (17)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

Results: 27 items found

View:

Order by

Date (Newest First)

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (127)

All Usage and Operation System Requirements & Setup (31) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (273)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (17)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

Extended Cold Start Guide

Extended Cold Start Guide

My laser has been inactive for a long time and will not fire.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

CO2 Laser Tickle Settings

CO2 Laser Tickle Settings

What are tickle settings and how can I adjust them?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

Replacing the Laser Tube

Replacing the Laser Tube

Replace your machine's CO2 laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. For this procedure you will need access to the back of the machine. Disconnect all exhaust system hoses from the rear of the machine. Using a 5/32” hex key, remove the screws that secure the rear (...)

120-Watt CO2 Laser Tube

120-Watt CO2 Laser Tube

Replace your machine's 120-watt CO2 laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws which secure the lower panel on the rear of the machine, then remove the panel Remove Old Laser Tube Use a Phillips screwdriver to loosen the (...)

CO2 Laser Tube Replacement 30 – 80 Watt

CO2 Laser Tube Replacement 30 – 80 Watt

How do I replace the CO2 laser tube on Fusion / M2 machine?

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the ten hex screws which secure the lower panel on the rear of the machine, then remove the panel. Remove Old Laser Tube Disconnect the black connector from the (...)

Fiber Laser Tube Replacement

Fiber Laser Tube Replacement

Replace your machine's fiber laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws that secure the lower panel on the rear of the machine, then remove the panel. Remove the top access panel on the left side of the (...)

Interlock Install – FiberMark

Interlock Install – FiberMark

How do I replace the interlocks on the FiberMark?

Please find the attachment for an in-depth description.

Fiber Laser Replacement – Fusion Pro 32 & 48

Fiber Laser Replacement – Fusion Pro 32 & 48

How do I replace the fiber laser in the Fusion Pro 32 and 48?

This document outlines the replacement of the fiber laser in the Fusion Pro 32 and 48.

How to Replace the CO₂ Laser Tube & RF Unit

How to Replace the CO₂ Laser Tube & RF Unit

How do I replace the CO2 laser tube and RF unit on my Fusion Pro 32 and 48?

Estimated time: 60–90 minutes • Skill: Intermediate This guide outlines the procedure for replacing CO₂ and 120-Watt laser tubes, as well as the RF unit, on Epilog laser systems. Following these steps ensures the components are removed, installed, and connected safely and correctly. For this procedure, you will need the (...)

Fiber Laser Replacement

Fiber Laser Replacement

How do I replace the fiber laser in the Fusion Maker, Edge, and Pro 24 and 36?

This document outlines the replacement of the fiber laser in the Fusion Maker, Edge, and Pro 24 and 36. After replacing the fiber laser, complete the laser alignment and focus calibration procedures.

JPT 50 Watt Fiber Laser Conversion – Fusion Pro 48

JPT 50 Watt Fiber Laser Conversion – Fusion Pro 48

How do I install the JPT 50- watt fiber laser conversion in the Fusion Pro 48?

This document outlines the installation of the JPT 50-watt fiber laser conversion kit in the Fusion Pro 48.

Front Door Interlock Replacement – Fusion Pro 32 & 48

Front Door Interlock Replacement – Fusion Pro 32 & 48

How do I replace the front door interlock in the Fusion Pro 32 and 48?

Please find the attachment for an in-depth description.

1
2
3

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

URL

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy