Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

X-Axis

Series: 8000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (5)

All Getting Started

Usage and Operation (89)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (37) Projects (11) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (4) X-Axis (8) Y-Axis (5) Table / Grid (6) Optics (1) Cameras (0) Laser Source (7) Power / Electrical (0) Chassis (1) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

Results: 8 items found

View:

Order by

Date (Newest First)

Filters

Categories:

Getting Started (5)

All Getting Started

Usage and Operation (89)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (37) Projects (11) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (4) X-Axis (8) Y-Axis (5) Table / Grid (6) Optics (1) Cameras (0) Laser Source (7) Power / Electrical (0) Chassis (1) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

X-Axis Belt Replacement – Mini / Helix

X-Axis Belt Replacement – Mini / Helix

How do I replace the x-axis belt on my Mini?

Estimated time: 15–20 minutes • Skill: Basic This guide walks you step-by-step through replacing the X-Axis belt on an Epilog Mini or Helix laser engraver. Follow each instruction carefully to ensure proper installation and avoid damaging your machine. Always power off and unplug the engraver before beginning. To complete this (...)

X-Axis Flex Cable Install – Mini / Helix

X-Axis Flex Cable Install – Mini / Helix

How do I replace the flex cable on my Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam. Picture 1 Remove I-Beam cover by loosening the two screws on the front side of the beam and the four screws on the rear if you (...)

X-Axis Rail Install

X-Axis Rail Install

How do I replace the x-axis rail on my Epilog Mini?

Machine Type: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver Small Philips head screw driver Flat head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit Intro: This procedure details steps to replacing the X-Axis rail on the Legend Mini. The X-Axis rail guides the (...)

X-Axis Linear Guide Install

X-Axis Linear Guide Install

How do I replace the linear bearing in my Epilog Mini?

Machine Types: Epilog Mini 18/24 Tools Needed: Large Philips head screw driver 3/32 Allen wrench Torx Screw Driver with 3/32 hex bit This procedure details steps to replacing the X-axis bearing set. The bearing set is the race and bearing bracket that guides the X-Axis carriage assembly from left to (...)

Restore Accuracy: Replacing the X-Axis Encoder Strip

Restore Accuracy: Replacing the X-Axis Encoder Strip

How do I replace the X-Axis encoder strip for my Epilog Mini, Helix, or FiberMark?

Estimated time: 20–30 minutes • Skill: Basic This guide explains how to replace the encoder strip and reader assembly on the Epilog Mini, Helix, or FiberMark laser system. The encoder strip is the thin clear plastic strip that the encoder reader reads to determine X-Axis position; replacing it restores reliable (...)

Full Guide: Removing the X-Axis Rail and Belt

Full Guide: Removing the X-Axis Rail and Belt

How do I replace the X-Axis belt on the FiberMark?

Estimated time: 30–45 minutes • Skill: Intermediate To replace the X-Axis belt on an Epilog FiberMark laser, you must remove the X-Axis rail to allow access to the bearing guard and proper belt routing. This procedure involves three phases: removing the rail, replacing the belt, and reinstalling the rail and (...)

X-Axis Assembly Install – FiberMark

X-Axis Assembly Install – FiberMark

How do I remove the FiberMark X-axis assembly?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

X-Axis Motor Install – FiberMark

X-Axis Motor Install – FiberMark

How do I replace the X-motor on the FiberMark?

Estimated time: 15–20 minutes • Skill: Basic This guide explains how to replace the X-motor on the Epilog FiberMark laser system. The X-motor is responsible for moving the lens carriage from left to right along the X-axis. Following these instructions will help you safely remove the old motor and install (...)

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

URL

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy