Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Laser Source

Series: 13000-14000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

Results: 7 items found

View:

Order by

Date (Newest First)

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Tech Specs

Fiber Laser Conversion – IPG to JPT

Fiber Laser Conversion – IPG to JPT

This guide covers the removal of the IPG laser out of the Fusion M2 and the subsequent installation of the JPT laser. Safety First: Ensure the machine is completely powered off and disconnected from the power cable before starting. Fiber Handling Warning: Be extremely careful when handling the yellow fiber (...)

Extended Cold Start Guide

Extended Cold Start Guide

My laser has been inactive for a long time and will not fire.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

CO2 Laser Tickle Settings

CO2 Laser Tickle Settings

What are tickle settings and how can I adjust them?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

120-Watt CO2 Laser Tube

120-Watt CO2 Laser Tube

Replace your machine's 120-watt CO2 laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws which secure the lower panel on the rear of the machine, then remove the panel Remove Old Laser Tube Use a Phillips screwdriver to loosen the (...)

CO2 Laser Tube Replacement 30 – 80 Watt

CO2 Laser Tube Replacement 30 – 80 Watt

How do I replace the CO2 laser tube on Fusion / M2 machine?

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the ten hex screws which secure the lower panel on the rear of the machine, then remove the panel. Remove Old Laser Tube Disconnect the black connector from the (...)

Fiber Laser Tube Replacement

Fiber Laser Tube Replacement

Replace your machine's fiber laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws that secure the lower panel on the rear of the machine, then remove the panel. Remove the top access panel on the left side of the (...)

Purchase or Print a New Laser Alignment Target

Purchase or Print a New Laser Alignment Target

Where can I buy or print out a new target for aligning my laser beam?

Accurate laser alignment is essential to achieving clean, precise engraving and cutting results. Over time, alignment targets can wear out or become damaged, which may impact the performance of your laser system. To help maintain optimal accuracy, replacement laser alignment targets are available and easy to obtain. You can purchase (...)

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Email

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy