Fusion Maker Laser Machine

Autofocus Calibration Wizard

Estimated Time: 2–5 Minutes | Skill Level: Basic The Autofocus Calibration Wizard allows the laser system to automatically determine the correct autofocus height using a calibrated reference surface. This process ensures accurate and consistent autofocus performance across supported materials. Running the Autofocus Calibration Wizard Open the Settings Menu (...)

03/24/2026

Focus Calibration Wizard

Step-by-step guide to using the Focus Calibration Wizard, available in firmware version 1.1.2.1 and later.

Estimated Time: 5–10 Minutes | Skill Level: Basic The Focus Calibration Wizard allows the laser system to automatically determine the optimal focal height for the installed lens. This process engraves a test pattern on anodized aluminum and identifies the focus position that produces the brightest mark. Running the (...)

03/16/2026

How to Set Up Graphics Software for Epilog Laser Systems

This guide provides step-by-step instructions for configuring and using popular graphic design software with Epilog Laser systems.

Software Setup CorelDRAW Setup Open CorelDRAW. Note: CorelDRAW Graphics Suite is the recommended CorelDraw version for use with Epilog Laser systems. Other versions, such as the Student or Standard version, may have different menu options and settings. Select Tools > Options > Global > Printing > Driver Compatibility. Choose Epilog (...)

03/30/2026

Pro 24, Pro 36

Autofocus Switch Replacement – Fusion Maker, Edge, Pro 24 & 36

How do I replace the autofocus switch in the Fusion Maker, Edge, and Pro 24 and 36?

This procedure outlines the steps required to safely and effectively replace the Autofocus Switch on the Fusion Maker, Edge, and Pro, laser system. The Autofocus Switch is a critical component responsible for maintaining the proper focal distance during operation. This document provides detailed instructions to ensure proper removal, and installation (...)

05/07/2025

Optics Cleaning – Fusion Maker, Edge, and Pro

This document details how to properly clean the Fusion Maker, Edge, and Pro carriage optics.

Daily Maintenance Cleaning Remove the lens and carriage mirror. Safely detach both the lens and carriage mirror using the video guide below. Figure 1. Lens and carriage mirror removal process. Carriage Optics Removal Steps Disconnect the air tubing from the lens. Loosen the thumb screws on the carriage cover and (...)

12/31/2025

My Artwork isn’t showing up in the Epilog Dashboard

My Artwork Isn’t Showing Up in the Epilog Dashboard and the Run Time Says 0:00?

Explanation of the Symptoms When encountering this issue, you may see something similar to the image below—here we can see the artwork in the preview thumbnail, but the artwork does not appear in the work area: However, if zoomed out, we can see that the artwork did transfer to the (...)

04/25/2025

Pro 24, Pro 36

Manual Focus Gauge Calibration – Fusion Maker, Edge, Pro

Learn how to calibrate the manual focus gauge on a Fusion Maker, Edge, or Pro machine.

This procedure outlines the steps required to calibrate the manual focus gauge after completing the Focus Calibration Wizard. Proper calibration ensures that the gauge accurately reflects the correct focal height determined using the Calibration Wizard. Note: The Calibration Wizard is available only on firmware version 1.1.2.1 or later. To update (...)

12/31/2025

Generating Machine Logs

How do I generate the machine logs?

Generating machine logs enables Epilog Technical Support to gather important information about the machine, aiding in its diagnosis and troubleshooting. The process is straightforward and requires either a USB flash drive or a network-connected machine. This guide will outline the steps for generating logs. Logs can be generated one of (...)

07/10/2026

Cleaning Procedures – Fusion Maker, Edge, and Pro

This document details the general cleaning and maintenance of the Fusion Maker, Edge, and Pro machine.

Regular cleaning of the Fusion Pro engraver will result in a longer service life of the engraver and less down time. Additionally, regular cleaning of the Fusion Pro engraver can mitigate the risk of flare-ups and other thermal events. A mild household cleaner or degreaser can be used to clean (...)

12/31/2025

CO2 Laser Replacement Checklist / Low Output

This guide will assist you in diagnosing and resolving low output issues with your 17000 series laser system.

Having to continually reduce speed and increase power can indicate low output from the laser. This document will help identify a low output laser tube on a 17000 Maker, Edge, or Pro machine. Checklist Optics Alignment Focus Reference Engraving Download the sample file below. Reference Engraving Open the file and (...)

04/09/2025

Pro 24, Pro 36

Control Module Replacement – Fusion Edge, Maker, Pro

The control module is a crucial component of your Fusion Maker, Fusion Edge, or Fusion Pro engraver, enabling seamless operation and precise control. This guide provides step-by-step instructions for safely removing and installing a new control module to ensure optimal performance. Following these procedures will help you maintain your engraver’s (...)

04/04/2025

Manipulating Clip Art to Create Unique Designs

How can I change a piece of clipart so it will engrave well?

One of the most common challenges we hear from customers has absolutely nothing to do with lasers. Instead, we hear a lot of laser operators looking for unique and creative artwork they can use to create samples or custom projects for customers. If your customer doesn’t supply you with a (...)

04/07/2025

Fusion Maker

Filters

Filters

Autofocus Calibration Wizard

Focus Calibration Wizard

How to Set Up Graphics Software for Epilog Laser Systems

Autofocus Switch Replacement – Fusion Maker, Edge, Pro 24 & 36

Optics Cleaning – Fusion Maker, Edge, and Pro

My Artwork isn’t showing up in the Epilog Dashboard

Manual Focus Gauge Calibration – Fusion Maker, Edge, Pro

Generating Machine Logs

Cleaning Procedures – Fusion Maker, Edge, and Pro

CO2 Laser Replacement Checklist / Low Output

Control Module Replacement – Fusion Edge, Maker, Pro

Manipulating Clip Art to Create Unique Designs