Skip to main content
Optics
16000-17000

Filters


Getting Started (11)
Usage and Operation (108)
Service and Repair (122)

Filters


Getting Started (11)
Usage and Operation (108)
Service and Repair (122)

Replacing a Lens with the Lens Removal Tool

Introduction

Over time, the lens in your laser’s lens tube can become scratched, pitted or clouded by smoke and debris that cleaning won’t remove. Instead of replacing the entire lens tube, the lens removal tool lets you swap out just the lens. The tool unscrews the brass retaining ring that holds the lens in place, its color bands show your lens’s focal length so you can set the new lens back at exactly the right height, and its back end holds the new lens so you can set it into the tube without touching it. It’s a quick job that takes about ten minutes and doesn’t require any special skills. This guide walks you through choosing the right tool for your machine, how the lens tube is put together, and how to remove the old lens and install the new one.

Which tool do I need?

There are three versions of the lens removal tool, one for each style of lens tube. They all work the same way, so the steps in this guide apply to every version.

Edge and Maker

All Edge and Maker machines use the LC small aperture lens tube. Order the LC small aperture tool, part no. LC1863.

Pro

Pro machines can use any of the three lens tube styles, and the model number alone doesn’t tell you which one you have. Remove your lens tube and compare it to the styles below.

LC small aperture lens tube

LC small aperture

Tool part no. LC1863

  • Outside diameter: 0.875 in (22.2 mm)
  • Same diameter as the CS tube; compare the shape to the photo
LC large aperture lens tube

LC large aperture

Tool part no. LC1864

  • Outside diameter: 1.15 in (29.2 mm)
  • Noticeably wider than the two small aperture tubes
CS small aperture lens tube

CS small aperture

Tool part no. CS1428

  • Outside diameter: 0.875 in (22.2 mm)
  • Same diameter as the LC small tube; compare the shape to the photo

Still not sure which tube you have? Contact support with your machine’s serial number and a photo of your lens tube.

What’s inside the lens tube

The lens tube is a threaded, hollow tube. The lens sits between two brass rings, along with a thin flexure (a small wave spring) that keeps gentle, even pressure on it. The top brass ring screws down to hold everything in place. You only remove the top brass ring; the bottom ring stays in the tube unless it needs adjusting.

Where the flexure goes depends on your lens:

  • 1.5 in and 2 in lenses, and the 4 in lens in the LC large aperture tube: the flexure sits on top of the lens.
  • 3 in lenses (CO2, fiber and dual) and the 4 in lenses in the CS tube: the flexure sits under the lens, on the bottom brass ring.
Labeled cross-section of the LC lens tube
LC lens tube
Labeled cross-section of the CS lens tube
CS lens tube

The Flexure column in each band table shows where the flexure goes for your lens.

Reading the tool’s color bands

Each tool has a set of colored bands that mark the lenses it works with. The LC tools have four bands and the CS tool has five; open the section for your tool below to see which band goes with which lens. Insert the tool into the top of the lens tube and rotate it until it seats in the notches of the top brass retaining ring. The color band that’s level with the top of the lens tube tells you the focal length of the lens. When you install the new lens, that same band is your reference: tighten the ring until it’s level with the top of the tube again, and the lens is at the correct height.

Each table also lists the lens tube assembly and the part number for the lens by itself, so you can order the right replacement lens.

The tool also has a hole through its body. If a ring is too tight to turn by hand, you can slide your machine’s focus tool, or another sturdy shaft, through the hole to use as a handle. Most of the time you won’t need it.

Lens sizes are focal lengths, not diameters. A 2 in lens focuses the beam 2 inches below the lens. It isn’t 2 inches across.

Select your tool to see its bands:

  • LC small aperture tool (LC1863) (click to show bands)
    LC small aperture lens removal tool with its bands labeled: white 1.5 in CO2, green 2 in CO2, red 3 in dual, yellow 3 in fiber only
    Lens focal length Band Lens tube assy Lens part no. Flexure
    1.5 in CO2 ⚪ White LC0418 FT0805 On top of lens
    2 in CO2 🟢 Green LC0230 260558 On top of lens
    3 in dual 🔴 Red LC0419 CS0826 Under lens
    3 in fiber only 🟡 Yellow LC0930 CS1085 Under lens
  • LC large aperture tool (LC1864) (click to show bands)
    LC large aperture lens removal tool with its bands labeled: white 1.5 in CO2, green 2 in and 4 in CO2, red 3 in dual, yellow 3 in CO2
    Lens focal length Band Lens tube assy Lens part no. Flexure
    1.5 in CO2 ⚪ White LC1297 LC1197 On top of lens
    2 in CO2 🟢 Green LC1145 LC1157 On top of lens
    4 in CO2 🟢 Green LC1296 LC1196 On top of lens
    3 in dual 🔴 Red LC1298 LC1198 Under lens
    3 in CO2 🟡 Yellow LC1311 LC1308 Under lens

    The 2 in and 4 in lenses both line up with the green band.

  • CS small aperture tool (CS1428) (click to show bands)
    CS small aperture lens removal tool with its five bands labeled: blue 2 in CO2 120 watt, white 2 in CO2 50 to 80 watt, green 3 in fiber, red 4 in CO2 50 to 80 watt, yellow 4 in CO2 120 watt
    Lens focal length Band Lens tube assy Lens part no. Flexure
    2 in CO2 (120 watt) 🔵 Blue CS0990 260558 On top of lens
    2 in CO2 (50–80 watt) ⚪ White CS0910 260558 On top of lens
    3 in fiber / dual 🟢 Green CS0993 CS0826 Under lens
    4 in CO2 (50–80 watt) 🔴 Red CS0991 CS0971 Under lens
    4 in CO2 (120 watt) 🟡 Yellow CS0992 FT0806 Under lens

    The blue and white bands sit close together, and so do the red and yellow bands. Check the wattage of your machine if you’re not sure which one you’re reading.

Before you begin

You’ll need

  • Lens removal tool for your tube type
  • Replacement lens with the same focal length (see the lens part numbers)
  • Powder-free nitrile gloves or finger cots
  • Lint-free lens tissue or a clean microfiber cloth
  • Cotton swab
  • Lens cleaner, such as MCP-303 Lens Cleaning Solution

Set up your workspace

  • Work on a clean, flat surface covered with a soft cloth
  • Use good lighting so you can see the brass rings clearly
  • Keep a small tray nearby so the flexure doesn’t get lost
  • Wear gloves the whole time; skin oils can damage the lens coating

Remove the old lens

Lens tube removed from the machine
Step 1

Remove the lens tube

Remove the lens tube from your machine. For step-by-step instructions, see Optics Cleaning – Fusion Maker, Edge, and Pro.

Lens removal tool seated in the lens tube with the green band level with the top of the tube
Step 2

Insert the tool and note your band

Hold the lens tube upright with the open top end facing up. Insert the tool into the top of the tube, then rotate it gently until it drops into and grabs the notches of the top brass ring.

The color band that’s level with the top of the lens tube tells you the focal length of your lens (see the band table). Remember this color. It’s your reference for setting the new lens at the correct height.

Lens removal tool in the lens tube with an arrow showing counterclockwise rotation; a focus gauge through the hole serves as an optional handle
Step 3

Unscrew the top brass ring

Hold the tube firmly and turn the tool counterclockwise by hand to unscrew the ring. Keep the tool straight; tilting it can scratch the inside of the tube.

Ring won’t budge? Only then, slide your machine’s focus tool (or another sturdy shaft) through the hole in the lens removal tool and use it as a handle to break the ring loose. Once it’s loose, take the handle out and finish unscrewing by hand.

Top brass ring, flexure and lens lifted out above the lens tube, in the order they come out
Step 4

Take out the parts

Hold the tube over your cloth and tip it gently so the top ring, flexure and lens slide out. Don’t use tweezers, screwdrivers or other metal tools to pry the lens out.

Keep the top ring and flexure; you’ll reuse them with the new lens.

If your lens has the flexure underneath (3 in lenses and CS 4 in lenses; see the Flexure column), it may stay on the bottom brass ring when the lens slides out. Tip the tube a little further to get it out, or leave it in place if it’s lying flat and undamaged.

Empty lens tube viewed from above, ready to inspect and clean
Step 5

Inspect and clean

Look inside the tube and wipe away any dust or debris with a lint-free cloth.

Install the new lens

Which side of the lens is curved?

Each lens is flat on one side and curved on the other. Once installed, the curved side always faces up, toward the top of the tube. Because you’ll load the lens into the tube upside down in step 6, that means the curved side goes down against the tool. On some lenses, especially longer focal lengths, the curve is so slight that both sides can look flat. Use these checks to tell them apart.

1. Look for an arrow

Some lenses have a small arrow on the edge. If yours does, it points toward the curved side. Not every lens has one.

2. Check your reflection

Hold the lens by its edges and look at your reflection in it. Then flip the lens over and look again. The side where your reflection is right-side up (not upside down) is the curved side. That’s the side that faces up in the tube, so place it face down on the tool when you load the lens in step 6.

3. Look at the edge

Hold the lens edge-on at eye level against a light background. The curved side bulges slightly past the edge, while the flat side stays level. This works best on shorter focal lengths, which have more curve.

New lens resting curved side down on the back end of the lens removal tool
Step 6

Load the lens onto the tool

Stand the tool upright on your work surface with its back end (the end opposite the notch tabs) facing up. Set the new lens on the back end of the tool with the curved side down, against the tool. If you’re not sure which side is curved, see Which side of the lens is curved?

3 in lens or CS 4 in lens (flexure under the lens): if you took the flexure out, set it flat on top of the lens now.

Orientation matters. A lens installed upside down will not focus correctly.

  • Upside-down lens tube being lowered over the lens resting on the back end of the tool
  • Lens tube seated upside down over the tool, with an arrow showing the two being flipped over together
  • Tool being lifted straight up out of the upright lens tube, leaving the lens inside


    Step 7

    Insert the lens into the tube

    1. Turn the lens tube upside down, so its open top end faces down.
    2. Lower the tube straight down over the lens and tool until the lens seats inside the tube.
    3. Holding the tube and tool together, flip them over so the tube is upright again.
    4. Lift the tool straight out of the top of the tube. The lens stays in the tube.

    Look into the tube and check that the lens is lying flat. If it’s tilted, nudge it flat with a cotton swab.

    Flexure and top brass ring going into the lens tube on top of the lens
    Step 8

    Add the flexure and top ring

    1.5 in or 2 in lens, or LC large aperture 4 in lens (flexure on top of the lens): drop the flexure in now so it lies flat on top of the lens.

    Place the top brass ring on top with its notches facing up, then start threading it by hand.

    Lens removal tool in the lens tube with an arrow showing clockwise rotation
    Step 9

    Tighten with the tool

    Insert the tool and turn clockwise by hand until your band is level with the top edge of the tube and the ring feels snug. Stop there.

    You don’t need the focus tool handle. Do not overtighten. The lens is fragile and can crack if overtightened.

    Ring went past your band, or got snug before reaching it? The bottom brass ring may need adjusting. See Adjusting the bottom brass ring.

    Reassembled lens tube viewed from above, with the top brass ring in place
    Step 10

    Check and reinstall

    Hold the tube up to a light and look through it. The lens should be centered, clean and free of fingerprints. Give the tube a light shake: nothing should rattle. Then reinstall the lens tube in your machine and run a test.

    Adjusting the bottom brass ring

    The bottom brass ring sets the height the lens sits at. Most of the time you won’t need to touch it. But when you tighten the top ring in step 9, your band should reach the top of the tube just as the ring gets snug. If it doesn’t, the bottom ring is at the wrong height. The bottom ring is adjusted from underneath, so the lens tube needs to be taken apart from the bottom. You only need to loosen the top ring, not remove it.

    What you see What it means What to do (working from the bottom)
    The top ring keeps turning past your band (band ends up below the top of the tube) The lens is sitting too low Raise the bottom ring: turn it clockwise
    The top ring gets snug before your band reaches the top of the tube The lens is sitting too high Lower the bottom ring: turn it counterclockwise
    Exploded view of the lens assembly.

    To adjust the bottom ring

    1. Loosen the top ring a few turns (step 3) so the lens isn’t clamped. You don’t need to take the top ring, flexure or lens out.
    2. Take apart the bottom of the lens assembly by following the Monthly Detailed Cleaning section of Optics Cleaning – Fusion Maker, Edge, and Pro. Stop once the inner lens cone is removed and you can reach the bottom brass ring from underneath.
    3. Insert the tool from the bottom and rotate it until it grabs the bottom ring’s notches.
    4. Turn the ring a small amount in the direction shown in the table. Start with one full turn; the threads are very fine, so each turn moves the ring only slightly. If the ring is stiff, slide the focus tool through the tool’s hole for leverage.
    5. Check the height before reassembling anything else: tighten the top ring from the top (step 9) and see whether your band lines up with the top of the tube just as the top ring gets snug.
    6. If it doesn’t, loosen the top ring again and repeat steps 3 to 5.
    7. Once the height is right, reassemble the bottom of the lens assembly by following the same optics cleaning instructions.

    Troubleshooting

    Was this helpful?

    Yes
    No
    Thanks for your feedback!
    • Date:
      11/19/2026

    Parts & Resources: