Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Zing

Series: 10000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (92)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (9) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (28)

All Service and Repair Troubleshooting (4) Control / Circuit Boards (2) X-Axis (6) Y-Axis (2) Table / Grid (1) Optics (1) Cameras (0) Laser Source (5) Power / Electrical (1) Chassis (0) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 128 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (92)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (9) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (28)

All Service and Repair Troubleshooting (4) Control / Circuit Boards (2) X-Axis (6) Y-Axis (2) Table / Grid (1) Optics (1) Cameras (0) Laser Source (5) Power / Electrical (1) Chassis (0) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Optimize Your Workflow: Changing Default Job Settings

Optimize Your Workflow: Changing Default Job Settings

How can I set up default job settings in the Software Suite?

Estimated time: 5–10 minutes • Skill: Beginner By default, jobs sent to the Epilog Software Suite use standard settings. You can customize these defaults to save setup time or better match your materials and applications. Follow the steps below to change the default job settings. Changing Default Job Settings Send (...)

Laser Exhaust Requirements

Laser Exhaust Requirements

What specifications should I be aware of when choosing an exhaust system?

Systems: All When specifying an exhaust system for your machine there are a number of considerations. The main minimum requirements that must be followed: CFM (Cubic Feet per Minute) or M3/hr (metric): This is the amount of air that a blower or exhaust system can move per hour of operation. The (...)

Bar Code Engraving Suggestions

Bar Code Engraving Suggestions

How can I engrave a very small bar code with the laser?

There are a lot of variables which determines whether your 2D barcode engraving will be successful. The contrast you can achieve on the PCB, the amount of data contained within the 2D barcode, size of barcode and most importantly, the scanner you’re using. When you’re trying to engrave a very (...)

How Do I Choose My Laser System’s Wattage?

How Do I Choose My Laser System’s Wattage?

How do I choose the correct wattage laser for my needs?

The power of the laser source is measured in watts. Depending on the machine you are considering you will have power options for your laser source that range from 30-120 watts for CO2 laser tubes. Generally speaking, lower power CO2 laser tubes will be able to process the same materials, (...)

How Much Combustible Gas is Released From Laser Engraving

How Much Combustible Gas is Released From Laser Engraving

Is laser engraving releasing dangerous combustible gases?

Combustible gas release from laser engraving is extremely minuscule. When materials are engraved with a laser, they emit combustion products. These consist largely of simple carbon smoke and debris. Gases are also produced; typical combustion gas products for some common engraving materials are shown below. The values are provided in (...)

YAG Laser vs. CO2 Lasers

YAG Laser vs. CO2 Lasers

What is the difference between a YAG and CO2 laser?

Two of the most common types of lasers you hear about are YAG and CO2. While Epilog manufactures a CO2 laser system, we wanted to give you some information about the two different types of laser systems and which one may be right for your application. Both CO2 lasers and (...)

Photo Engraving Do’s and Don’ts

Photo Engraving Do’s and Don’ts

How can I create a great photo engraving with the laser?

Photographs are one of the most popular items for engraving purposes. Taking a captured memory and engraving it upon a different material such as wood or marble truly takes photographs to the next level. Here we’ll cover the do’s and don’ts that will make all your photo engraved projects picture (...)

Engraver Table Weight Limits

Engraver Table Weight Limits

How much weight can the Epilog engraver table hold?

Engraver Model Maximum Static Table Weight* Maximum Lifting Table Weight** Fusion Maker 12/24/36 90 lbs (40.8 kg) 60 lbs (27.2 kg) Fusion Edge 12/24/36 90 lbs (40.8 kg) 60 lbs (27.2 kg) Fusion Pro 24/36 Vector Grid: 60 lbs (27.2 kg) Task Plate: 90 lbs (40.8 kg) 60 lbs (27.2 (...)

1
...
9
10
11

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Comments

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy