Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Knowledge Base

Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 274 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Replacing Optics

Replacing Optics

Replace the lens that focuses your laser.

Remove the Current Lens Begin by Jogging the lens assembly closer to the front of the machine. To do this, select the Jog Menu icon, then use the joystick to move the lens assembly. Lower the table a few inches to give you some clearance to work. You can accomplish (...)

Replacing Optics

Replacing Optics

Replace the lens that focuses your laser.

Remove Lens Assembly Remove the lens assembly by loosening the three thumb screws on its front face until they spin freely. They are captive screws and will not come out of the assembly. Slide the assembly out of its housing. Remove Old O-Ring and Lens With the lens assembly in (...)

Lens Carriage Rollers

Lens Carriage Rollers

Replace the rollers that ensure smooth travel of your lens assembly.

Remove Lens Assembly Shut off the laser and remove the power cord from the machine. Move the X-Axis Assembly to the center of the machine and the lens carriage to the center of the table. Loosen the two screws which secure the lens carriage to the belt assembly. As you (...)

Controller Board

Controller Board

Replace the controller board that acts as the brain of your laser machine.

Record Settings If your machine will boot up, we’ll start by writing down some settings that will save you time later. Press the Go and Pointer button at the same time to access the Function menu and cycle through the headings by pressing the Go button. Write down the Serial (...)

Controller Board

Controller Board

Replace the controller board that acts as the brain of your laser machine.

Remove Old Control Board Shut off the laser and remove the power cord from the machine. Remove any Ethernet and USB cables from the back of the machine. Put on the anti-static wrist strap. Always wear the anti-static strap when handling the control board to avoid damaging the unit through (...)

Replacing the Laser Tube

Replacing the Laser Tube

Replace your machine's CO2 laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. For this procedure you will need access to the back of the machine. Disconnect all exhaust system hoses from the rear of the machine. Using a 5/32” hex key, remove the screws that secure the rear (...)

120-Watt CO2 Laser Tube

120-Watt CO2 Laser Tube

Replace your machine's 120-watt CO2 laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws which secure the lower panel on the rear of the machine, then remove the panel Remove Old Laser Tube Use a Phillips screwdriver to loosen the (...)

CO2 Laser Tube Replacement 30 – 80 Watt

CO2 Laser Tube Replacement 30 – 80 Watt

How do I replace the CO2 laser tube on Fusion / M2 machine?

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the ten hex screws which secure the lower panel on the rear of the machine, then remove the panel. Remove Old Laser Tube Disconnect the black connector from the (...)

Fiber Laser Tube Replacement

Fiber Laser Tube Replacement

Replace your machine's fiber laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws that secure the lower panel on the rear of the machine, then remove the panel. Remove the top access panel on the left side of the (...)

Replacing the Reducer Drive Assembly

Replacing the Reducer Drive Assembly

Replace the Reducer Drive Assembly for the X-Motor of your machine.

Remove Panels First, power off and unplug the machine. Using a 5/32” Allen Key, remove the right side panel from the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. Manually move the x-axis assembly to the middle of the engraver. Remove the X-axis assembly (...)

Control Board Install – FiberMark

Control Board Install – FiberMark

How do I replace the FiberMark Controller Board?

Please find the attachment for an in-depth description.

Top Door Replacement – Fusion / Fusion M2

Top Door Replacement – Fusion / Fusion M2

How do I replace the Fusion and Fusion M2 Door Assembly?

Please find the attachment for an in-depth description.

1
...
13
14
15
16
17
...
23

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Phone

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy