Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Knowledge Base

Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 274 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Lens Camera Board and USB-C Cable Replacement – Fusion Pro 32 & 48

Lens Camera Board and USB-C Cable Replacement – Fusion Pro 32 & 48

How do I replace the lens camera board in the Fusion Pro 32 and 48?

This procedure outlines how to replace both the Carriage Camera PCB and the X-Axis USB-C cable on a 16000 Series Fusion Pro laser system. The Carriage Camera PCB also integrates the Auto Focus sensor, which is critical to system performance. Follow each step carefully to ensure proper installation and avoid (...)

Linear Guide (IKO) Replacement – Fusion Pro 32 & 48

Linear Guide (IKO) Replacement – Fusion Pro 32 & 48

How do I replace the linear guide in the Fusion Pro 32 and 48?

This document outlines the replacement of the linear guide in the Fusion Pro 32 and 48.

Vision System Repair: Replacing the Overhead Camera

Vision System Repair: Replacing the Overhead Camera

How to replace the overhead camera in the Fusion Pro 32 and 48.

Estimated time: 30–45 minutes • Skill: Intermediate This guide outlines the procedure for replacing the overhead camera on the Epilog Fusion Pro 32 and 48 laser systems. Following these steps will ensure the camera is removed, installed, and updated correctly. For this procedure, you will need the required part: CS0834 (...)

X-Axis Idler Replacement – Fusion Maker, Edge, Pro 24 & 36

X-Axis Idler Replacement – Fusion Maker, Edge, Pro 24 & 36

How do I replace the x-axis idler in the Fusion Maker, Edge, and Pro 24 and 36?

This document outlines the replacement of the x-axis idler in the Fusion Maker, Edge, and Pro 24 and 36.

Fusion Maker, Edge, Pro 24 & 36 – Linear Guide (Rev 1 IKO) Replacement

Fusion Maker, Edge, Pro 24 & 36 – Linear Guide (Rev 1 IKO) Replacement

How do I replace the linear guide in the Fusion Maker, Edge, and Pro 24 and 36?

This document provides concise, step‑by‑step instructions for removing and installing the X‑Axis linear guide (IKO rail) on Fusion Edge, Maker, and Pro 24/36 engravers. Read the entire procedure before beginning, observe all safety precautions (power off and disconnect), and have the required hand tools ready. Follow each step in order (...)

Y-Axis Reducer Drive Belt Replacement -Fusion / Fusion M2

Y-Axis Reducer Drive Belt Replacement -Fusion / Fusion M2

How do I replace the Y-Axis drive belt on my Fusion and Fusion M2 machine?

The attached PDF contains the Y-Axis reducer drive belt installation instructions.

Encoder Strip Install

Encoder Strip Install

How do I install the encoder strip in my 36EXT?

The attached document will guide you through replacing the encoder strip on a 36EXT.

X-Axis Reducer Drive Replacement – Fusion Edge, Pro 24 & 36

X-Axis Reducer Drive Replacement – Fusion Edge, Pro 24 & 36

How do I replace the x-axis reducer in the Fusion Edge and Pro 24 and 36?

This document outlines the replacement of the x-axis reducer in the Fusion Edge and Pro 24 and 36.

Table Belt Replacement

Table Belt Replacement

How do I replace the z-axis belt in the Fusion Maker, Edge, and Pro 24 and 36?

This document outlines the replacement of the z-axis belt in the Fusion Maker, Edge, and Pro 24 and 36.

X-Axis PCB Replacement

X-Axis PCB Replacement

How do I replace the x-axis PCB in the Fusion Maker, Edge, and Pro 24 and 36?

This document outlines the replacement of the x-axis PCB in the Fusion Maker, Edge, and Pro 24 and 36.

Encoder Reader Installation

How do I install the encoder reader on my 36EXT?

This procedure outlines the steps necessary to replace the X-axis encoder reader on the Legend EXT machine. The X-axis encoder reader is a crucial component for accurate movement tracking of the lens carriage assembly. Over time, this part may need maintenance or replacement to ensure continued precision and smooth operation (...)

Y-Axis Home Switch Replacement

Y-Axis Home Switch Replacement

How do I replace the y-axis home switch in the Fusion Pro 32 and 48?

This document outlines the replacement of the y-axis home switch in the Fusion Pro 32 and 48.

1
...
19
20
21
22
23

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Company

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy