Service and Repair

Estimated time: 30–45 minutes • Skill: Intermediate This guide outlines the procedure for replacing the overhead camera on the Epilog Fusion Pro 32 and 48 laser systems. Following these steps will ensure the camera is removed, installed, and updated correctly. For this procedure, you will need the required part: CS0834 (...)

Vision System Repair: Replacing the Overhead Camera

How to replace the overhead camera in the Fusion Pro 32 and 48.

Estimated time: 20–30 minutes • Skill: Intermediate This procedure guides you through removing and replacing the Overhead Camera on Fusion Edge and Fusion Pro engravers. Following these steps ensures the camera assembly is installed correctly, and the system is updated and calibrated for accurate camera-based alignment and job preview functionality. (...)

Vision System Repair: Replacing the Overhead Camera

How do I replace the overhead camera in the Fusion Maker, Edge, and Pro 24 / 36?

The X-Axis Air Assist (AA) Tubing Replacement process for the Fusion Pro 32 and 48 engravers ensures proper air flow during operation. Over time, the tubing may wear out and require replacement to maintain optimal performance. This guide provides step-by-step instructions on how to safely remove and install new AA (...)

X-Axis Air Assist (AA) Tubing Replacement – Fusion Pro 32 & 48

How do I replace the air assist tubing in the Fusion Pro 32 and 48?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

X-Axis Assembly Install – FiberMark

How do I remove the FiberMark X-axis assembly?

X-Axis Assembly Removal First, power off and unplug the machine. Using a 5/32” Allen Key, remove the right side panel from the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. Manually move the x-axis assembly to the middle of the engraver. Remove the lens (...)

X-Axis Assembly Replacement

Replace the rail that runs across the x-axis of your machine.

Remove Right Side Panel Shut off the laser and remove the power cord from the machine. Inside the machine, move the x-axis assembly to the rear of the machine. Put on the anti-static strap. Clip the strap on to any metal part of the machine. Always wear the anti-static strap (...)

X-Axis Assembly Replacement

Replace the gantry that runs across the x-axis of your machine.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

X-Axis Assembly Replacement

Replace the gantry that runs across the x-axis of your machine.

Remove Panels With the machine powered on, use the control panel to scroll down to ‘Jog.’ Then use the joystick to move the x-axis assembly toward the middle of the machine to give you room to work. Shut off the laser and remove the power cord from the machine. Remove (...)

X-Axis Assembly Replacement

Replace the gantry that runs across the x-axis of your machine.

This document outlines the replacement of the x-axis assembly in the Fusion Maker, Edge, and Pro 24 and 36.

X-Axis Assembly Replacement – Fusion Maker, Edge, Pro 24 & 36

How do I replace the x-axis assembly in the Fusion Maker, Edge, and Pro 24 and 36?

This document outlines the replacement of the x-axis assembly in the Fusion Pro 32 and 48.

X-Axis Assembly Replacement – Fusion Pro 32 & 48

How do I replace the x-axis assembly in the Fusion Pro 32 and 48?

This procedure provides detailed, step-by-step instructions for removing and reinstalling the X-Axis I-Beam on the Legend 36EXT laser system. Proper handling and alignment of the I-Beam are essential to ensure accurate motion and optimal performance of the machine. Please follow all safety guidelines and use the recommended tools to perform (...)

X-Axis Assembly Replacement – Legend 36EXT

How do I replace the X-Axis rail In my Legend 36 EXT?

04/11/2025

This guide outlines the complete procedure for safely removing and installing the X-Axis assembly in a Fusion Pro laser system. Carefully follow each step to maintain alignment, prevent component damage, and ensure optimal system performance during reassembly. Removal Power OFF the machine and disconnect the power cable. Remove the right (...)

X-Axis Assembly Replacement (Large Aperture)

05/27/2025

X-Axis Belt Install – 36EXT

How do I replace the X-axis belt on my 36EXT?

The attached document will provide instructions on installing the X-axis belt of a 36EXT machine.

This guide outlines the step-by-step process for replacing the X-axis belt on your laser machine. Before beginning, ensure the machine is powered off and properly prepared for service. Each section includes detailed instructions and corresponding images to help you complete the procedure safely and efficiently. Please follow all notes and (...)

X-Axis Belt Install – Fusion / Fusion M2

How do I replace the Fusion X-Axis Belt?

Please find the attachment for an in-depth description.

X-Axis Belt Install – Zing

How do I replace the Zing X-axis belt?

This document outlines the replacement of the x-axis belt in the Fusion Edge, and Pro.

X-Axis Belt Replacement – Fusion Edge and Pro

How do I replace the x-axis belt in the Fusion Edge, and Pro?