Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Fusion Edge

Series: 17000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (8)

All Getting Started

Usage and Operation (105)

All Usage and Operation System Requirements & Setup (26) Machine Control & Settings (1) Laser Techniques (12) Software Techniques (39) Projects (14) Rotary (2) FAQ (10)

Service and Repair (66)

All Service and Repair Troubleshooting (6) Control / Circuit Boards (6) X-Axis (12) Y-Axis (3) Table / Grid (5) Optics (0) Cameras (3) Laser Source (7) Power / Electrical (2) Chassis (3) Accessories (0) Calibrations (13) Cleaning (6)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 178 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (8)

All Getting Started

Usage and Operation (105)

All Usage and Operation System Requirements & Setup (26) Machine Control & Settings (1) Laser Techniques (12) Software Techniques (39) Projects (14) Rotary (2) FAQ (10)

Service and Repair (66)

All Service and Repair Troubleshooting (6) Control / Circuit Boards (6) X-Axis (12) Y-Axis (3) Table / Grid (5) Optics (0) Cameras (3) Laser Source (7) Power / Electrical (2) Chassis (3) Accessories (0) Calibrations (13) Cleaning (6)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Leveling the Table

Leveling the Table

How do I level the table in the Fusion Maker, Edge, and Pro 24 and 36?

This guide covers leveling the table on the Fusion Maker, Fusion Edge and Fusion Pro 24 and 36: leveling the table tub at the lead screws, leveling the table inserts (Pro only), and confirming the level with autofocus. Parts Required None Tools / Materials Required 5/32" Allen Wrench 1/8" Allen (...)

Adjusting the Home and Park Positions

Adjusting the Home and Park Positions

How do I adjust the home and park positions in the Fusion Maker, Fusion Edge, and Fusion Pro?

This guide covers checking and adjusting the X and Y home position, the rotary home position and the park positions on the Fusion Maker, Fusion Edge and Fusion Pro 24, 32, 36 and 48. Parts Required None Tools / Materials Required Ruler, Measuring Tape or Calipers Scrap material that marks (...)

X-Axis Belt Tensioning Guide

X-Axis Belt Tensioning Guide

How do I tension the X-Axis belt on my Fusion Edge, Maker, or Pro?

Identifying X-Axis Rail Version Before you begin, determine which version of the X-Axis rail is installed in your machine. Check the right side of the X-Axis rail: if there is no cutout, you have Revision 1; if there is a cutout, you have Revision 2. Follow the corresponding procedure based (...)

Carriage Optics Removal and Installation

Carriage Optics Removal and Installation

How do I remove and install the carriage optics in my laser?

Proper removal and installation of the carriage optics in the Fusion 17000 laser system are essential for maintaining optimal performance and precision. This guide provides step-by-step instructions for safely removing and reinstalling key components, including the mirror, lens tube, and air assist tubing. Following these procedures ensures that the optics (...)

Extended Cold Start Guide

Extended Cold Start Guide

My laser has been inactive for a long time and will not fire.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

CO2 Laser Tickle Settings

CO2 Laser Tickle Settings

What are tickle settings and how can I adjust them?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

Replacing the Control Panel

Replacing the Control Panel

Replace your machine's display panel.

Replacing the Control Panel We’re going to walk you through replacing the control panel on the Epilog Fusion Edge laser system. Turn off and unplug the machine. Remove Panel Using a 5/32″ Hex Key, remove the 8 screws that secure the right-hand side access panel and set them to the (...)

Power Supply Replacement

Power Supply Replacement

Replace your machine's power supply.

Remove Old Power Supply Now move to the rear of the machine. Using the 5/32″ Allen Wrench, remove the 9 screws that secure the rear panel to the machine. Locate the power supply housing. It is located to the left of the exhaust port as you face the machine from (...)

X-Motor Replacement

X-Motor Replacement

Replace the motor that moves your machine's laser head along the x-axis assembly.

Remove Side Panel Before we begin, make sure you turn off & unplug the machine. Using a 5/32” Allen wrench, remove the 8 Allen screws that secure the right-hand side panel, and set the panel off to one side. Move to the front of the machine and pull the X-axis (...)

Y-Motor Replacement

Y-Motor Replacement

Replace the motor that moves your machine's x-axis assembly forward and backward.

Remove Panels Turn off and unplug the machine. Each Fusion Edge is fitted with two Y motors. Determine which Y Motor, left or right-hand side, you will be replacing and remove that side panel from the machine. Using a 5/32″ Allen wrench, remove the 8 screws that secure the left (...)

Replacing the Laser Tube

Replacing the Laser Tube

Replace your machine's CO2 laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. For this procedure you will need access to the back of the machine. Disconnect all exhaust system hoses from the rear of the machine. Using a 5/32” hex key, remove the screws that secure the rear (...)

Blurry Driver Screen On Windows 10

Blurry Driver Screen On Windows 10

Why am I seeing a blurry driver screen on my Windows 10 High-Resolution Display?

This article explains how to fix an Epilog print driver window that looks very small or blurry on a Windows 10 computer. The problem is usually caused by the computer’s display driver or display scaling settings, not by the Epilog driver. Issue Summary After upgrading to Windows 10, or after (...)

1
...
7
8
9
10
11
...
15

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Company

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy