Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Fusion / Fusion M2

Series: 13000-14000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 142 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Bearing Rails

Bearing Rails

Keep your bearing rails clean to promote smooth performance.

To begin the procedure of cleaning and greasing the bearing rails, shut off the laser and remove the power cord from the machine. Clean the Bearing Rails Manually position the lens assembly to one side. Apply rubbing alcohol to a cotton swab. Clean one end of the bearing rail by (...)

Laser Alignment – Fusion Fibermark

Laser Alignment – Fusion Fibermark

How do I align the laser for the Fusion FiberMark?

Proper laser alignment is critical to the cutting performance and engraving quality of your Epilog Fusion FiberMark. This diagnostic guide outlines the complete step-by-step alignment procedure required to safely restore optimal beam delivery. Whether you are correcting a general loss of power, addressing beam fading in specific table zones, or (...)

Focus Calibrations

Focus Calibrations

How do I calibrate the Fusion M2/32/40 focus?

Please find the attachment for an in-depth description.

Table level Procedure

Table level Procedure

How do I adjust the Fusion table level?

Please find the attachment for an in-depth description.

Extended Cold Start Guide

Extended Cold Start Guide

My laser has been inactive for a long time and will not fire.

Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)

CO2 Laser Tickle Settings

CO2 Laser Tickle Settings

What are tickle settings and how can I adjust them?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

Replacing the Control Panel

Replacing the Control Panel

Replace your machine's display panel/keypad.

Remove Panel Remove the top access panel on the right side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Remove Old Keypad From beneath, locate and disconnect the wire harnesses from the back side of the key pad. (...)

Power Supply Replacement

Power Supply Replacement

Replace your machine's power supply.

Remove Panel Remove the lower access panel on the right side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter clockwise. Remove Old Power Supply Disconnect the power leads connecting the power supply assembly to the various components of (...)

RF Power Supply Replacement

RF Power Supply Replacement

Replace RF power supply that powers your laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Remove the bottom access panel on the left side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Remove Old RF Power Supply Unscrew the (...)

Safety Module

Safety Module

Replace the Fusion M2's safety status module.

Remove Panel Shut off the laser and remove the power cord from the machine. Remove the top access panel on the right side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Remove Old Safety Module Locate the Laser (...)

X-Motor Replacement

X-Motor Replacement

Replace the motor that moves your machine's laser head along the x-axis assembly.

Remove Side Panels With the machine powered on, use the control panel to scroll down to ‘Jog.’ Then use the joystick to move the x-axis assembly toward the middle of the machine to give you room to work. Shut off the laser and remove the power cord from the machine. (...)

X-Axis Assembly Replacement

X-Axis Assembly Replacement

Replace the gantry that runs across the x-axis of your machine.

Remove Panels With the machine powered on, use the control panel to scroll down to ‘Jog.’ Then use the joystick to move the x-axis assembly toward the middle of the machine to give you room to work. Shut off the laser and remove the power cord from the machine. Remove (...)

1
...
4
5
6
7
8
...
12

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

URL

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy