Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Fusion / Fusion M2

Series: 13000-14000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 142 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (93)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (0) FAQ (9)

Service and Repair (41)

All Service and Repair Troubleshooting (5) Control / Circuit Boards (3) X-Axis (7) Y-Axis (4) Table / Grid (2) Optics (2) Cameras (0) Laser Source (7) Power / Electrical (2) Chassis (1) Accessories (1) Calibrations (4) Cleaning (3)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Restore X-Axis Homing: Replacing the Home (Limit) Sensors

Restore X-Axis Homing: Replacing the Home (Limit) Sensors

Replacing the X and Y home (limit) switches in a Fusion / M2

Remove Panels We’ll start by replacing the left sensor, then move on to the right sensor. Shut off the laser and remove the power cord from the machine. Remove the top access panels on both the left and right side of the machine by using a 5/32” hex key to (...)

X-Axis Tensioning Belt

X-Axis Tensioning Belt

Adjust the belt that helps control your laser head's movement.

Remove Panel Shut off the laser and remove the power cord from the machine. Remove the top access panel on the left side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Adjust Belt Tension Use a 7/64” hex (...)

Y-Axis Assembly

Y-Axis Assembly

Replace the assemblies that guide forward and backward movement of your lens assembly.

Remove Panels Shut off the laser and remove the power cord from the machine. We’ll begin by replacing the y-axis on the right-hand side of the machine. Use a 5/32” hex key to remove the exhaust plenum on the rear of the machine. Then remove the small panel in the (...)

Y-Axis Sensors

Y-Axis Sensors

Replace the sensors that help your y-axis motor achieve accurate positioning.

Remove Panel We’ll start by replacing the front sensor, then move on to the rear sensor. Shut off the laser and remove the power cord from the machine. Remove the top access panel on the left side of the machine by using a 5/32” hex key to turn the black (...)

Y-Motor Replacement

Y-Motor Replacement

Replace the motor that moves your machine's x-axis assembly forward and backward.

Remove Panels Remove the top access panel on the right side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Use a 5/32” hex key to remove the two main panels on the back of the machine. Remove Old (...)

Z-Motor / Table Motor Replacement

Z-Motor / Table Motor Replacement

Replace the motor that controls your machine's table height.

Remove Bottom Right Panel Shut off the laser and remove the power cord from the machine. Remove the bottom access panel on the right side of the machine by using a 5/32” hex key to turn the black panel locks ¾ of the way counter-clockwise. Mark Tensioning Position Begin by (...)

Replacing Optics

Replacing Optics

Replace the lens that focuses your laser.

Remove Lens Assembly Remove the lens assembly by loosening the three thumb screws on its front face until they spin freely. They are captive screws and will not come out of the assembly. Slide the assembly out of its housing. Remove Old O-Ring and Lens With the lens assembly in (...)

Controller Board

Controller Board

Replace the controller board that acts as the brain of your laser machine.

Remove Old Control Board Shut off the laser and remove the power cord from the machine. Remove any Ethernet and USB cables from the back of the machine. Put on the anti-static wrist strap. Always wear the anti-static strap when handling the control board to avoid damaging the unit through (...)

120-Watt CO2 Laser Tube

120-Watt CO2 Laser Tube

Replace your machine's 120-watt CO2 laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws which secure the lower panel on the rear of the machine, then remove the panel Remove Old Laser Tube Use a Phillips screwdriver to loosen the (...)

CO2 Laser Tube Replacement 30 – 80 Watt

CO2 Laser Tube Replacement 30 – 80 Watt

How do I replace the CO2 laser tube on Fusion / M2 machine?

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the ten hex screws which secure the lower panel on the rear of the machine, then remove the panel. Remove Old Laser Tube Disconnect the black connector from the (...)

Fiber Laser Tube Replacement

Fiber Laser Tube Replacement

Replace your machine's fiber laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws that secure the lower panel on the rear of the machine, then remove the panel. Remove the top access panel on the left side of the (...)

Top Door Replacement – Fusion / Fusion M2

Top Door Replacement – Fusion / Fusion M2

How do I replace the Fusion and Fusion M2 Door Assembly?

Please find the attachment for an in-depth description.

1
...
5
6
7
8
9
...
12

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Company

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy