Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Legend 36EXT

Series: 9000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (1)

All Getting Started

Usage and Operation (89)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (9) Software Techniques (38) Projects (11) Rotary (0) FAQ (9)

Service and Repair (30)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (2) X-Axis (8) Y-Axis (3) Table / Grid (1) Optics (0) Cameras (0) Laser Source (6) Power / Electrical (1) Chassis (0) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 119 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (1)

All Getting Started

Usage and Operation (89)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (9) Software Techniques (38) Projects (11) Rotary (0) FAQ (9)

Service and Repair (30)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (2) X-Axis (8) Y-Axis (3) Table / Grid (1) Optics (0) Cameras (0) Laser Source (6) Power / Electrical (1) Chassis (0) Accessories (0) Calibrations (4) Cleaning (2)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

RF Unit Replacement – Legend 36EXT

RF Unit Replacement – Legend 36EXT

How do I replace the RF unit in my Legend 36EXT?

This guide covers replacing the RF (radio frequency) unit in the Legend 36EXT. The RF unit is vital to the laser’s operation, and correct replacement keeps it performing consistently and reliably. Parts Required RF Unit Tools Required Phillips Screwdriver Small Flat Head Screwdriver Safety First: Ensure the engraver is completely (...)

X-Axis Motor Replacement – Legend 36EXT

X-Axis Motor Replacement – Legend 36EXT

This document details the X-Axis motor installation on a Legend 36EXT.

This guide covers replacing the X-axis motor in the Legend 36EXT, including tensioning the X-axis belt afterward. Parts Required X-Axis Motor Tools Required 5/32" Allen Wrench Phillips Screwdriver Safety First: Ensure the engraver is completely powered off and the power cord is disconnected before removing any panels or touching internal (...)

Laser Replacement – Legend 36EXT

Laser Replacement – Legend 36EXT

This article explains how to replace the CO2 laser tube in a Legend 36EXT.

This guide covers replacing the CO2 laser tube in the Legend 36EXT. Handle the laser carefully during removal and installation to avoid damaging it. Parts Required CO2 Laser Tube Tools Required Phillips Screwdriver Safety First: Ensure the engraver is completely powered off and the power cord is disconnected before removing (...)

Laser Troubleshooting Guide: Replacing the Safety Interlocks

How do I replace the safety interlocks on the Legend 36EXT.

Estimated time: 15–20 minutes • Skill: Beginner This guide outlines the procedure for replacing the window and door interlocks on an Epilog Legend 36 EXT laser system. These safety interlocks are designed to prevent the laser from firing when access panels are open. If they are damaged or not functioning (...)

Autofocus Plunger Replacement – Legend 36EXT

Autofocus Plunger Replacement – Legend 36EXT

This document provides detailed instructions on replacing the autofocus sensor in a legend 36 EXT

This guide covers replacing the autofocus sensor (plunger) on the Legend 36EXT. Refer to the exploded view of the X-carriage assembly for part names. Parts Required Autofocus Sensor (Plunger) Tools Required Phillips Screwdriver 5/64" Allen Wrench Safety First: Make sure the engraver is turned off before you begin. Sensor Removal (...)

Power Supply Replacement – Legend 36EXT

Power Supply Replacement – Legend 36EXT

This document details how to replace the power supply in a legend 36 EXT.

This guide covers replacing the power supply bundle in the Legend 36EXT. Parts Required Power Supply Bundle Tools / Materials Required Phillips Screwdriver Wire Cutters Cable Tie Safety First: Always disconnect the power cord from the engraver before beginning, to prevent electrical shock or equipment damage. Power Supply Removal Step (...)

Quick Guide: Replacing the Control Board

Quick Guide: Replacing the Control Board

How to replace the control board on a Legend 36 EXT.

Estimated time: 20–30 minutes • Skill: Intermediate This procedure will guide you through the process of removing and replacing the main controller board in a Legend EXT laser system. Following these steps ensures safe handling of sensitive electronics, proper reconnection, and minimal downtime after installation. Important: Always wear the included (...)

Manipulating Clip Art to Create Unique Designs

Manipulating Clip Art to Create Unique Designs

How can I change a piece of clipart so it will engrave well?

One of the most common challenges we hear from customers has absolutely nothing to do with lasers. Instead, we hear a lot of laser operators looking for unique and creative artwork they can use to create samples or custom projects for customers. If your customer doesn’t supply you with a (...)

Focus Lens 101

Focus Lens 101

How does the focus lens work on the laser?

This Technical Library article discusses the purpose of the focus lens as well as guidelines for using lenses of different sizes for various projects. What does a focus lens do? A laser beam emanating from the laser tube is typically around one-quarter of an inch (240 thousandths) in diameter. This (...)

Reducing Fire Hazards with your Laser

Reducing Fire Hazards with your Laser

How do I make sure my laser is safe from fire hazards?

This article will guide you through recommendations to reduce fire hazard with your laser. Your laser system uses a high intensity beam of light that can generate extremely high temperatures when it comes into contact with the material being engraved, marked or cut. Some materials are extremely flammable and can (...)

Make Your Own FontBot

Make Your Own FontBot

How do I create an image out of fonts, like a FontBot?

What is a FontBot? It’s a design you create from the letters and characters of a specific font. Designers have come up with all kinds of amazing robots and other creations using fonts, but what will yours look like? We’ll be giving a quick demonstration on how to create your (...)

Everything You Wanted to Know about Fonts…and Then Some!

Everything You Wanted to Know about Fonts…and Then Some!

How do I use fonts in my designs for the laser?

Regardless of your design program, you’re likely faced with a myriad of fonts to select from when you’re creating a design. But how do you choose fonts? What types of fonts go with what kind of designs? How can you manipulate text and fonts to create appealing visuals? Read on (...)

1
2
3
4
5
...
10

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

URL

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy