Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Service and Repair

Series: 8000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (94)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (1) FAQ (9)

Service and Repair (50)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (5) X-Axis (9) Y-Axis (4) Table / Grid (6) Optics (1) Cameras (0) Laser Source (8) Power / Electrical (2) Chassis (1) Accessories (0) Calibrations (5) Cleaning (6)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 50 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (9)

All Getting Started

Usage and Operation (94)

All Usage and Operation System Requirements & Setup (20) Machine Control & Settings (1) Laser Techniques (10) Software Techniques (38) Projects (14) Rotary (1) FAQ (9)

Service and Repair (50)

All Service and Repair Troubleshooting (3) Control / Circuit Boards (5) X-Axis (9) Y-Axis (4) Table / Grid (6) Optics (1) Cameras (0) Laser Source (8) Power / Electrical (2) Chassis (1) Accessories (0) Calibrations (5) Cleaning (6)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Cleaning the Encoder Strip: Essential Maintenance for Accurate Printing

Cleaning the Encoder Strip: Essential Maintenance for Accurate Printing

A clean linear encoder strip helps your machine achieve accurate positioning.

Procedure Power down and unplug the machine. For your safety, completely turn off the laser system and disconnect the power cord from the back of the machine before beginning. Loosen the assembly cover screws. Using a Phillips head screwdriver, loosen the seven screws that secure the X-Axis assembly cover. There (...)

Controller Board

Controller Board

Replace the controller board that acts as the brain of your laser machine.

Record Settings If your machine will boot up, we’ll start by writing down some settings that will save you time later. Press the Go and Pointer button at the same time to access the Function menu and cycle through the headings by pressing the Go button. Write down the Serial (...)

X-Motor Replacement

X-Motor Replacement

Replace the motor that moves your machine's laser head along the x-axis assembly.

Remove Side Panels Shut off the laser and remove the power cord from the machine. Remove the left side panel by loosening the four screws on its main face, as well as the two screws on the back. Remove the right side panel by loosening the four screws on its (...)

Blurry Driver Screen On Windows 10

Blurry Driver Screen On Windows 10

Why am I seeing a blurry driver screen on my Windows 10 High-Resolution Display?

Please find the attachment for an in-depth description

Interlock Install – FiberMark

Interlock Install – FiberMark

How do I replace the interlocks on the FiberMark?

Please find the attachment for an in-depth description.

X-Axis Assembly Install – FiberMark

X-Axis Assembly Install – FiberMark

How do I remove the FiberMark X-axis assembly?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

Laser Installation – FiberMark

Laser Installation – FiberMark

How do I replace the laser on the FiberMark?

Please find the attachment for an in-depth description.

Interlock Install – Mini / Helix

Interlock Install – Mini / Helix

How do I replace the Helix/Mini interlocks?

Interlock sensor replacement instructions for the Mini and Helix engraver.

Table Belt Install – Mini / Helix

Table Belt Install – Mini / Helix

How do I replace the Helix Z-belt?

Please find the attachment for an in-depth description.

Y-Axis Slider Block Install – Mini / Helix

Y-Axis Slider Block Install – Mini / Helix

How do I replace the Mini/Helix slider blocks?

Y-Axis slider block replacement for the Mini and Helix engravers.

Y-Axis PCB Install – Mini / Helix

Y-Axis PCB Install – Mini / Helix

How do I replace the Mini/Helix X/Y Combo PCB?

Please find the attachment for an in-depth description.

X-Axis Encoder Reader Install – Mini / Helix

X-Axis Encoder Reader Install – Mini / Helix

How do I replace the Mini/Helix X-axis encoder reader?

This article provides step-by-step instructions for replacing the X-axis encoder read head in Epilog Laser engravers, specifically for the Mini 18×12, Mini 24×12, and Helix 24×18 models. The procedure outlined below will guide you through the necessary steps to successfully replace the read head, ensuring that the X-axis system functions (...)

1
2
3
4
5

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

X/Twitter

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy