Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Knowledge Base

Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 448 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (47)

All Getting Started

Usage and Operation (128)

All Usage and Operation System Requirements & Setup (32) Machine Control & Settings (2) Laser Techniques (13) Software Techniques (41) Projects (26) Rotary (3) FAQ (10)

Service and Repair (274)

All Service and Repair Troubleshooting (10) Control / Circuit Boards (32) X-Axis (69) Y-Axis (21) Table / Grid (20) Optics (9) Cameras (8) Laser Source (27) Power / Electrical (11) Chassis (12) Accessories (2) Calibrations (35) Cleaning (18)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Troubleshooting Guide

Troubleshooting Guide

Troubleshooting the Zing Engraver

Revision: Sept. 17, 26 • Hardware Maintenance Guide Most of the problems below trace back to one of three things: a dirty sensor, a loose belt, or something out of alignment in the optics. Work through the matching section below, in order — most fixes take a few minutes with (...)

Blurry Driver Screen On Windows 10

Blurry Driver Screen On Windows 10

Why am I seeing a blurry driver screen on my Windows 10 High-Resolution Display?

Please find the attachment for an in-depth description

Backplane Install – Zing

Backplane Install – Zing

How do I replace the Zing backplane board?

Please find the attachment for an in-depth description.

Rotary Motor Install – Fusion / Fusion M2

Rotary Motor Install – Fusion / Fusion M2

How do I replace the Fusion rotary motor?

Please find the attachment for an in-depth description.

Top Door Replacement – Fusion / Fusion M2

Top Door Replacement – Fusion / Fusion M2

How do I replace the Fusion and Fusion M2 Door Assembly?

Please find the attachment for an in-depth description.

Control Board Install – FiberMark

Control Board Install – FiberMark

How do I replace the FiberMark Controller Board?

Please find the attachment for an in-depth description.

Replacing the Reducer Drive Assembly

Replacing the Reducer Drive Assembly

Replace the Reducer Drive Assembly for the X-Motor of your machine.

Remove Panels First, power off and unplug the machine. Using a 5/32” Allen Key, remove the right side panel from the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. Manually move the x-axis assembly to the middle of the engraver. Remove the X-axis assembly (...)

Fiber Laser Tube Replacement

Fiber Laser Tube Replacement

Replace your machine's fiber laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws that secure the lower panel on the rear of the machine, then remove the panel. Remove the top access panel on the left side of the (...)

CO2 Laser Tube Replacement 30 – 80 Watt

CO2 Laser Tube Replacement 30 – 80 Watt

How do I replace the CO2 laser tube on Fusion / M2 machine?

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the ten hex screws which secure the lower panel on the rear of the machine, then remove the panel. Remove Old Laser Tube Disconnect the black connector from the (...)

120-Watt CO2 Laser Tube

120-Watt CO2 Laser Tube

Replace your machine's 120-watt CO2 laser tube.

Remove Panel Shut off the laser and remove the power cord from the machine. Use a 5/32” hex key to remove the hex screws which secure the lower panel on the rear of the machine, then remove the panel Remove Old Laser Tube Use a Phillips screwdriver to loosen the (...)

Replacing the Laser Tube

Replacing the Laser Tube

Replace your machine's CO2 laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. For this procedure you will need access to the back of the machine. Disconnect all exhaust system hoses from the rear of the machine. Using a 5/32” hex key, remove the screws that secure the rear (...)

Controller Board

Controller Board

Replace the controller board that acts as the brain of your laser machine.

Remove Old Control Board Shut off the laser and remove the power cord from the machine. Remove any Ethernet and USB cables from the back of the machine. Put on the anti-static wrist strap. Always wear the anti-static strap when handling the control board to avoid damaging the unit through (...)

1
...
27
28
29
30
31
...
38

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

URL

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy