Service and Repair Archives

Quick Guide: Calibrating the Joystick for Accurate Movement

Calibrating the joystick can resolve issues like delayed movement, inaccurate control, or the carriage drifting on its own while in jog mode.

Steps to Calibrate the Joystick Open the Settings Menu On the display panel, press the gear icon in the top-right corner to open the Settings menu. Image 1: Home screen with gear icon in top-right corner Access Advanced Settings Press and hold the word “Settings” on the screen until the (...)

03/16/2026

Pro 24/36, Pro 32/48

IRIS Camera Calibration Guide

How do I calibrate the IRIS camera system in the Maker, Edge, Pro, and Ascent?

Estimated Time: 20–40 Minutes • Skill Level: Intermediate Important: All focus calibration procedures must be completed before performing a camera calibration to ensure accurate results. Click the tabs below to switch between machine types. Each tab shows the camera calibration procedure specific to that machine. Overview & Requirements Fusion Edge (...)

04/15/2026

X-Axis Belt Tensioning Guide

How do I tension the X-Axis belt on my Fusion Edge, Maker, or Pro?

Identifying X-Axis Rail Version Before you begin, determine which version of the X-Axis rail is installed in your machine. Check the right side of the X-Axis rail: if there is no cutout, you have Revision 1; if there is a cutout, you have Revision 2. Follow the corresponding procedure based (...)

09/29/2026

Adjusting the Home and Park Positions

How do I adjust the home and park positions in the Fusion Maker, Fusion Edge, and Fusion Pro?

This guide covers checking and adjusting the X and Y home position, the rotary home position and the park positions on the Fusion Maker, Fusion Edge and Fusion Pro 24, 32, 36 and 48. Parts Required None Tools / Materials Required Ruler, Measuring Tape or Calipers Scrap material that marks (...)

11/03/2026

Pro 24, Pro 36

Leveling the Table

How do I level the table in the Fusion Maker, Edge, and Pro 24 and 36?

This guide covers leveling the table on the Fusion Maker, Fusion Edge and Fusion Pro 24 and 36: leveling the table tub at the lead screws, leveling the table inserts (Pro only), and confirming the level with autofocus. Parts Required None Tools / Materials Required 5/32" Allen Wrench 1/8" Allen (...)

11/05/2026

Pro 24, Pro 36

Fiber Laser Alignment

How do I align the fiber laser in the Fusion Maker, Edge, and Pro 24 and 36?

Fiber laser alignment is a crucial maintenance procedure to ensure the optimal performance of your Fusion Edge and Fusion Pro laser engravers. Over time, misalignment can occur due to regular use, component replacement, or moving the machine to a new location. This guide provides a step-by-step process for checking and (...)

12/31/2025

Pro 24, Pro 36

Touchpad Calibration – Fusion Maker, Edge, and Pro 24 and 36

How do I calibrate the touchpad on the Fusion Maker, Edge, and Pro 24 and 36?

Estimated time: 5 minutes • Skill: Basic Touchscreen calibration ensures accurate touch response when selecting options and settings on the display. This procedure is rarely required and should only be performed if the touchscreen is registering incorrect inputs or responding inconsistently. Touchscreen Calibration Procedure Open the Settings menu. At the (...)

01/27/2026

Pro 32, Pro 48

Fiber Alignment – Fusion Pro 32 & 48

How do I align the laser in my Fusion Pro Fiber or Dual source machine.

This guide covers aligning the fiber laser on a dual source Fusion Pro 32 or 48. The fiber laser is aligned to the CO2 laser’s beam path using the two fiber mirrors and the fiber laser’s red dot pointer. The fiber laser is not fired during this procedure. Parts Required (...)

11/03/2026

Pro 24, Pro 36

Focus Calibrations – Fusion Maker, Edge, and Pro

How do I calibrate the focus in the Fusion Maker, Fusion Edge, and Fusion Pro?

This guide covers focus calibration procedures for older firmware on the Fusion Maker, Fusion Edge and Fusion Pro 24, 32, 36 and 48. If your machine is running current firmware, refer to the Focus Calibration Wizard documentation instead. Focus calibrations keep the engraver working at the correct focal height. Parts (...)

11/03/2026

Pro 24, Pro 36

Laser Alignment – Maker / Edge / Pro

Adjust your optics system's mirrors to ensure your laser fires precisely.

Turn On To begin the laser alignment procedure, power on the laser. For the following procedures, the table will be broken into four (4) positions. Each position is identified by its relative distance to the laser source and corresponds with the mirror to adjust for that position. Three of the (...)

12/31/2025

Pro 24, Pro 36

Cleaning Your Optics

Cleaning your lens and mirrors is an essential part of routine maintenance.

Cleaning the Focusing Lens Optics The mirrors in the periscope housing are enclosed, and will likely require cleaning less often than the other components of the optics system. Let’s start by jogging the laser assembly toward the front of the machine for access to the optics, then we’ll turn off (...)

10/01/2026

Pro 24, Pro 36

Top Door Replacement

How do I replace the top door on my Fusion Edge 24?

This guide covers removing and replacing the top door on the Fusion Edge 24. The control panel and right top cover are removed to reach the right hinge. All directions are given as if you are standing at the front of the engraver. Parts Required Replacement Top Door Tools Required (...)

11/05/2026

Service and Repair

Filters

Filters

Quick Guide: Calibrating the Joystick for Accurate Movement

IRIS Camera Calibration Guide

X-Axis Belt Tensioning Guide

Adjusting the Home and Park Positions

Leveling the Table

Fiber Laser Alignment

Touchpad Calibration – Fusion Maker, Edge, and Pro 24 and 36

Fiber Alignment – Fusion Pro 32 & 48

Focus Calibrations – Fusion Maker, Edge, and Pro

Laser Alignment – Maker / Edge / Pro

Cleaning Your Optics

Top Door Replacement