FiberMark Archives

X-Axis Assembly Install – FiberMark

How do I remove the FiberMark X-axis assembly?

Estimated time: 30–45 minutes • Skill: Intermediate This guide explains how to remove and reinstall the X-Axis assembly on the Epilog FiberMark laser engraver. Removing the X-Axis rail is necessary for tasks such as replacing the X-Axis belt or servicing the bearing guard on the underside of the rail. You’ll (...)

10/02/2025

Laser Installation – FiberMark

How do I replace the laser on the FiberMark?

Please find the attachment for an in-depth description.

09/24/2024

X-Axis Motor Install – FiberMark

How do I replace the X-motor on the FiberMark?

Estimated time: 15–20 minutes • Skill: Basic This guide explains how to replace the X-motor on the Epilog FiberMark laser system. The X-motor is responsible for moving the lens carriage from left to right along the X-axis. Following these instructions will help you safely remove the old motor and install (...)

10/02/2025

Repairing Y-Axis Movement: Replacing the Y-Motor

Replace the motor that moves the rail front to back in the Y-Axis.

Estimated time: 15–20 minutes • Skill: Basic This guide explains how to replace the Y-motor on the Epilog FiberMark laser system. The Y-motor drives the X-Axis assembly forward and backward. Following these instructions will help you safely remove the old motor and install the new one. Procedure Disconnect the machine (...)

10/14/2025

Table Motor Install – FiberMark

How do I replace the Z-motor on the FiberMark?

Please find the attachment for an in-depth description.

09/24/2024

Y-Axis Slider Block Install – FiberMark

How do I replace the FiberMark slider blocks?

Please find the attachment for an in-depth description.

09/24/2024

Interlock Install – Mini / Helix

How do I replace the Helix/Mini interlocks?

Interlock sensor replacement instructions for the Mini and Helix engraver.

09/24/2024

Table Belt Install – Mini / Helix

How do I replace the Helix Z-belt?

Please find the attachment for an in-depth description.

09/24/2024

Y-Axis Slider Block Install – Mini / Helix

How do I replace the Mini/Helix slider blocks?

Y-Axis slider block replacement for the Mini and Helix engravers.

09/24/2024

Y-Axis PCB Install – Mini / Helix

How do I replace the Mini/Helix X/Y Combo PCB?

Please find the attachment for an in-depth description.

09/24/2024

X-Axis Encoder Reader Install – Mini / Helix

How do I replace the Mini/Helix X-axis encoder reader?

This article provides step-by-step instructions for replacing the X-axis encoder read head in Epilog Laser engravers, specifically for the Mini 18×12, Mini 24×12, and Helix 24×18 models. The procedure outlined below will guide you through the necessary steps to successfully replace the read head, ensuring that the X-axis system functions (...)

04/08/2025

Checking and Leveling the Table

If you notice uneven engraving or reduced power in specific corners of your Mini or Helix, the table may be out of level. This guide explains how to check and level the table for optimal performance.

Estimated time: 15-20 minutes • Skill: Beginner A perfectly level engraving table is essential for accurate focusing and consistent engraving results. This guide will walk you through checking and adjusting the table level on your Epilog Mini or Helix laser system. Checking Table Level Access the table. Power on the (...)

06/30/2026

FiberMark

Filters

Filters

X-Axis Assembly Install – FiberMark

Laser Installation – FiberMark

X-Axis Motor Install – FiberMark

Repairing Y-Axis Movement: Replacing the Y-Motor

Table Motor Install – FiberMark

Y-Axis Slider Block Install – FiberMark

Interlock Install – Mini / Helix

Table Belt Install – Mini / Helix

Y-Axis Slider Block Install – Mini / Helix

Y-Axis PCB Install – Mini / Helix

X-Axis Encoder Reader Install – Mini / Helix

Checking and Leveling the Table