Backplane Board Replacement – Fusion Galvo
This document outlines the replacement of the backplane board in the G100.
Blurry Driver Screen On Windows 10
Please find the attachment for an in-depth description
Camera Board Replacement – G100
This guide provides step-by-step instructions for removing and replacing the overhead camera assembly in the G100 laser system. Follow all instructions carefully and ensure power is disconnected before performing any maintenance. Camera Removal Turn off the machine. Disconnect the machine from power. Loosen and remove the top screws. Remove the (...)
CO2 Laser Tickle Settings
Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)
Control Module Replacement
This guide provides step-by-step instructions for replacing the control board in the G100 system. Always wear an anti-static strap and disconnect power before beginning any maintenance procedure. Control Board Removal Turn off the engraver. Disconnect the power cable. Locate the door handles. Open the door. Loosen and remove screws. Loosen, (...)
Door Belt Replacement – G100
This guide outlines the steps to replace the right-side door lift belt. The left-side replacement procedure is identical. Please follow all safety protocols before beginning. Door Belt Removal Turn off engraver Disconnect from power Loosen and remove screws Remove panel Loosen and remove Remove panel Loosen and remove Remove panel (...)
Door Damper Replacement – Fusion Galvo
This guide provides step-by-step instructions for replacing the door damper on Epilog Laser G100 series systems. The procedure shown covers the replacement of the GC0233 (right side door damper), but the steps are identical for the GC0232 (left side door damper). Before starting, verify the part number on your replacement (...)
Door Motor Replacement – Fusion Galvo
This guide provides step-by-step instructions for replacing the door motor on Epilog Laser G100 series systems. The process includes removing the door, installing the new motor, and reassembling the engraver. Be sure to follow all recommended safety precautions throughout the procedure. Door Motor Removal Turn off engraver Disconnect from power (...)
Door Slide Replacement – Fusion Galvo
This guide provides step-by-step instructions for replacing the door slide on Epilog Laser G100 series systems. The process includes removing the door, installing the new slide, and reassembling the engraver. Be sure to follow all recommended safety precautions throughout the procedure. Door Slide Removal Turn off engraver Disconnect from power (...)
Extended Cold Start Guide
Lasers that have been inactive for a period of time may not fire right away. There are settings in the machine to help warm the laser before use. Please start with the CO2 Laser Tickle Settings guide first. If the laser has been inactive for an extended period of time, (...)
LC1000 – Control Module Port and LED Overview
The control module on Epilog laser systems provides connection points and LED indicators that offer system status and control feedback. This guide outlines each port and indicator located on the right side of the machine. Port Descriptions Exhaust Control: Connects to a compatible exhaust unit to send on/off commands. USB (...)
Lens Replacement
This guide provides step-by-step instructions for replacing the lens assembly in the G100 model engraver. Please review all steps carefully before beginning the procedure. Make sure the machine is powered off and the work area is prepared to avoid damage to components. If you need further assistance during or after (...)
My Artwork isn’t showing up in the Epilog Dashboard
Explanation of the Symptoms When encountering this issue, you may see something similar to the image below—here we can see the artwork in the preview thumbnail, but the artwork does not appear in the work area: However, if zoomed out, we can see that the artwork did transfer to the (...)
Purchase or Print a New Laser Alignment Target
Accurate laser alignment is essential to achieving clean, precise engraving and cutting results. Over time, alignment targets can wear out or become damaged, which may impact the performance of your laser system. To help maintain optimal accuracy, replacement laser alignment targets are available and easy to obtain. You can purchase (...)
Red Dot Diode Replacement – Fusion Galvo
This document outlines the replacement of the red dot diode assembly in the G100.
Rotary Circuit Board Replacement – Fusion Galvo G100
Replacing the rotary circuit board on the Fusion Galvo G100 laser is a critical maintenance procedure designed to restore or maintain optimal rotary function. This guide provides step-by-step instructions for safely accessing, removing, and installing the rotary circuit board. Proper handling and installation are essential to ensure continued precision and (...)
SD Card Installation – Fusion Galvo
Installing an SD card in the Fusion Galvo laser system is a crucial step for maintaining system functionality and ensuring smooth operation. This guide provides detailed, step-by-step instructions for safely removing and replacing the SD card, including necessary precautions such as using an anti-static bracelet to prevent damage. Additionally, it (...)
Table Motor Replacement – Fusion Galvo
This document outlines the replacement of the z-axis motor in the Fusion Galvo.
Updating the IRIS Camera System
This document outlines the IRIS camera system update procedure in the Fusion Maker, Fusion Edge, and Fusion Pro.