Skip to main content

Epilog Support

Knowledge Base
Training

Support Resources

Software & Firmware Downloads
Owner's Manuals
Register Your Machine
Remote Session
Support Process
Explore Epiloglaser.com

Submit a Ticket

Knowledge Base
Training
Resources

Service and Repair

Series: 16000-17000
Laser Machine:

Drivers & Software

Manual Downloads

Filters

Categories:

Getting Started (11)

All Getting Started

Usage and Operation (107)

All Usage and Operation System Requirements & Setup (27) Machine Control & Settings (2) Laser Techniques (12) Software Techniques (39) Projects (14) Rotary (2) FAQ (10)

Service and Repair (119)

All Service and Repair Troubleshooting (6) Control / Circuit Boards (12) X-Axis (34) Y-Axis (5) Table / Grid (8) Optics (4) Cameras (6) Laser Source (11) Power / Electrical (4) Chassis (5) Accessories (0) Calibrations (16) Cleaning (8)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Results: 119 items found

View:

Order by

Relevance

Filters

Categories:

Getting Started (11)

All Getting Started

Usage and Operation (107)

All Usage and Operation System Requirements & Setup (27) Machine Control & Settings (2) Laser Techniques (12) Software Techniques (39) Projects (14) Rotary (2) FAQ (10)

Service and Repair (119)

All Service and Repair Troubleshooting (6) Control / Circuit Boards (12) X-Axis (34) Y-Axis (5) Table / Grid (8) Optics (4) Cameras (6) Laser Source (11) Power / Electrical (4) Chassis (5) Accessories (0) Calibrations (16) Cleaning (8)

Machine Resources:

Drivers & Software
Manual Downloads
Material Settings
Tech Specs

Power Supply Replacement – Fusion Pro 32 & 48

Power Supply Replacement – Fusion Pro 32 & 48

How do I replace the power supply in the Fusion Pro 32 and 48?

Power Supply Locations CO2- Only Fusion Pro This model will contain only the CO2 power supply shown above. One (1) 48V 2kW power supply Fiber- Only Fusion Pro This model will contain the CO2 and fiber power supplies shown above One (1) 48V 2kW power supply One (1) 24V 1kW (...)

CO2 Laser Tickle Settings

CO2 Laser Tickle Settings

What are tickle settings and how can I adjust them?

Introduced in the Epilog Mini and Helix engravers, laser tickle settings allow the user to customize certain CO2 laser characteristics by modifying the radio frequency (RF) signals sent to the laser tube. The role of the RF signal is to excite and energize the gas mixture within the CO2 laser (...)

Replacing the Control Panel

Replacing the Control Panel

Replace the display panel on the Fusion Pro 32 or 48.

Replacing the Control Panel Before we begin, turn off and unplug the Fusion Pro. Using a 5/32” Allen Key, remove the right side panel from the machine. Open the display panel package you received and put on the anti-static strap. Clip the strap onto any metal part of the machine. (...)

Power Supply Replacement

Power Supply Replacement

Replace your machine's power supply.

Remove Old Power Supply Now move to the rear of the machine. Using the 5/32″ Allen Wrench, remove the screws securing the upper rear panel to access the Power Supply. Locate the Power Supply under the access panel. Now carefully disconnect all of the wires plugged into the back of (...)

Replacing the X-Axis Belt on the Fusion Pro

Replacing the X-Axis Belt on the Fusion Pro

Replace the belt that runs across the X-axis Assembly of your machine.

Loosen X-Belt Start by powering of and unplugging the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. At the left side of the engraver, loosen the four idler mounting screws located on the front side of the x-axis assembly, and the four idler mounting (...)

X-Motor Replacement

X-Motor Replacement

Replace the motor that moves your machine's laser head along the x-axis assembly.

Remove Side Panel Before we begin, make sure you turn off & unplug the machine. Using a 5/32” Allen wrench, remove the 8 Allen screws that secure the right-hand side panel, and set the panel off to one side. Move to the front of the machine and pull the X-axis (...)

X-Axis Assembly Replacement

X-Axis Assembly Replacement

Replace the rail that runs across the x-axis of your machine.

X-Axis Assembly Removal First, power off and unplug the machine. Using a 5/32” Allen Key, remove the right side panel from the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. Manually move the x-axis assembly to the middle of the engraver. Remove the lens (...)

Replacing Optics

Replacing Optics

Replace the lens that focuses your laser.

Remove the Current Lens Begin by Jogging the lens assembly closer to the front of the machine. To do this, select the Jog Menu icon, then use the joystick to move the lens assembly. Lower the table a few inches to give you some clearance to work. You can accomplish (...)

Replacing the Laser Tube

Replacing the Laser Tube

Replace your machine's CO2 laser tube.

Remove Panels Shut off the laser and remove the power cord from the machine. For this procedure you will need access to the back of the machine. Disconnect all exhaust system hoses from the rear of the machine. Using a 5/32” hex key, remove the screws that secure the rear (...)

Replacing the Reducer Drive Assembly

Replacing the Reducer Drive Assembly

Replace the Reducer Drive Assembly for the X-Motor of your machine.

Remove Panels First, power off and unplug the machine. Using a 5/32” Allen Key, remove the right side panel from the machine. Using a 5/32” Allen Key, remove the left side panel from the machine. Manually move the x-axis assembly to the middle of the engraver. Remove the X-axis assembly (...)

Blurry Driver Screen On Windows 10

Blurry Driver Screen On Windows 10

Why am I seeing a blurry driver screen on my Windows 10 High-Resolution Display?

Please find the attachment for an in-depth description

Top Door Replacement

Top Door Replacement

How do I replace the top door on my Fusion Edge 24?

Please find the attachment for an in-depth description.

1
...
4
5
6
7
8
...
10

Need additional help?

Submit a ticket with our Technical Support Team

Submit a Ticket

Product

Product Line
Applications
Start a Laser Business

Support

Support Process
Submit a Ticket
Shop Parts & Accessories

Company

About Us
Careers
Contact Us
Find Your Rep

Sign up for our Newsletter

"*" indicates required fields

Company

This field is for validation purposes and should be left unchanged.

First name*

Last name*

Email

Epilog is proud to be an American company. Since 1988 we have been designing, engineering, and supporting our laser machines in Golden, Colorado.

© Epilog Laser | All Rights Reserved. | Privacy Policy